Installation
INSTALLATION1. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
(a) Engage the 3 pins.
(b) Install the 7 bolts ,
Torque: 20 Nm (204 kgf-cm, 15 ft.-lbf) (Bolt )
(c) Connect each of the clamps and the connectors, and install the bolt.
2. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
(a) Engage the 2 clips and install the cowl side trim subassembly LH.
3. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT: Use the same procedures for the RH side and the LH side.
4. INSTALL FRONT DOOR SCUFF PLATE LH
5. INSTALL FRONT DOOR SCUFF PLATE RH
HINT: Use the same procedures for the RH side and the LH side.
6. INSTALL FRONT PILLAR GARNISH LH
7. INSTALL FRONT PILLAR GARNISH RH
HINT: Use the same procedures for the RH side and the LH side.
8. CONNECT FRONT PASSENGER AIRBAG CONNECTOR
9. INSTALL INSTRUMENT PANEL NO.2 FINISH PANEL LOWER
(a) Install the 7 screws
10. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
(a) Install the 2 clips.
(b) Install the glove compartment door damper clip and the glove compartment door assembly.
11. INSTALL CONSOLE BOX ASSEMBLY
(a) Cover the parts indicated in the illustration with protective tape to prevent them from being damaged.
(b) Engage the 2 clips and install the console box assembly.
NOTICE: Do not damage the instrument panel safety pad when installing the console box assembly.
(c) Remove the attached protective tape from the console box assembly.
(d) Install the 2 bolts
(e) Install the 2 console caps and the 2 screws .
(f) Install the 3 screws
12. INSTALL FRONT SEAT ARMREST ASSEMBLY CENTER
(a) Install the bolt and front seat armrest assembly center.
Torque: 37 Nm (377 kgf-cm, 27 ft.-lbf)
(b) Engage the 2 claws and install the seat armrest cover LH.
13. INSTALL FLOOR CARPET COVER CENTER LH
(a) Install the 2 clips and the floor carpet cover center LH.
14. INSTALL FLOOR CARPET COVER CENTER RH
HINT: Use the same procedures for the RH side and the LH side.
15. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY CENTER
(a) Connect the connectors.
(b) Engage the 4 clips and the 2 claws, and install the instrument cluster finish panel assembly center.
16. INSTALL INSTRUMENT PANEL INSERT SUBASSEMBLY LOWER LH
(a) Install the 3 bolts
17. INSTALL INSTRUMENT PANEL FINISH PANEL SUBASSEMBLY LOWER
(a) Connect the hood lock control cable.
(b) Connect the connectors.
(c) Engage the 3 clips.
(d) Install the 2 bolts and the instrument panel finish panel sub-assembly lower.
18. INSTALL COMBINATION METER ASSEMBLY
(a) Connect the connectors.
(b) Install the 3 screws
19. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH
(a) Engage the claw.
(b) Install the 4 screws
20. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
(a) Engage the 5 clips and install the instrument cluster finish panel assembly.
21. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER
(a) Connect the connectors.
(b) Engage the 5 clips and install the instrument panel finish panel lower.
22. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY (w/ Navigation System)
23. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY (w/o Navigation System)
24. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER
(a) Engage the 8 clips and install the instrument cluster finish panel sub-assembly center.
25. INSTALL WIPER SWITCH
26. INSTALL HEADLIGHT DIMMER SWITCH
27. INSTALL STEERING COLUMN COVER UPPER
28. INSTALL STEERING COLUMN COVER LOWER
29. INSTALL STEERING WHEEL ASSEMBLY
30. INSTALL STEERING PAD
31. INSTALL STEERING WHEEL NO.3 COVER LOWER
32. INSTALL STEERING WHEEL NO.2 COVER LOWER
33. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
34. PERFORM INITIALIZATION
NOTICE: Some systems need initialization when disconnecting the cable from the negative battery terminal.
35. INSPECT STEERING PAD
36. INSPECT SRS WARNING LIGHT