Part 2

MANUAL TRANSMISSION UNIT

Components:

REASSEMBLY(continued)

26. INSTALL NO. 1 SHIFT DETENT BALL SPRING SEAT
a. Install the 2 shift detent ball low side compression springs and 2 shift detent balls into the intermediate plate.

b. Using a "Torx" socket wrench T40, install the 3 shift detent ball spring seats No. 1 onto the intermediate plate.
Torque: 18.5 Nm (189 kgf-cm, 14 ft. lbs.)

c. Install the shift detent ball and the shift detent ball low side compression spring into the intermediate plate.

d. Using a "Torx" socket wrench T40, install the shift detent ball spring seat No. 1 onto the intermediate plate.
Torque: 18.5 Nm (189 kgf-cm, 14 ft. lbs.)

27. INSTALL TRANSMISSION MAGNET
a. Clean the transmission magnet, and install it onto the intermediate plate.

28. INSTALL MANUAL TRANSMISSION CASE
a. Apply seal packing to the manual transmission case as shown in the illustration.
Seal packing: Part No.08826-00090, THREE BOND 1281 or equivalent.

b. Using a plastic hammer, tap the manual transmission case to attach it to the intermediate plate.

29. INSTALL NO. 1 COUNTER GEAR FRONT BEARING SNAP RING
a. Using a snap ring expander, install the counter gear front bearing snap ring No. 1 onto the transmission case.

30. INSTALL FRONT BEARING SHAFT SNAP RING
a. Using a snap ring expander, install the front bearing shaft snap ring onto the transmission case.

31. INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL
a. Using SST and a hammer, install the new transmission front bearing retainer oil seal onto the transmission front bearing retainer.
SST 09950-60010 (09951-00300, 09951-00520, 09952-06010), 09950-70010 (09951-07100)
Drive in depth: 11.2 to 12.2 mm (0.4409 to 0.4803 inch)
b. Coat the lip of the oil seal with MP grease.

32. INSTALL FRONT BEARING RETAINER
a. Apply seal packing to the bearing retainer front as shown in the illustration.
Seal packing: Part No.08826-00090, THREE BOND 1281 or equivalent.

b. Install the front bearing retainer onto the transmission case with the 8 bolts.
Torque: 16.5 Nm (168 kgf-cm, 12 ft. lbs.)
c. Check that the input shaft and output shaft rotate smoothly

33. INSTALL TRANSFER ADAPTER OIL SEAL
a. Using SST and a hammer, install the new transfer adapter oil seal onto the transfer adapter.
SST 09710-30050, 09950-70010 (09951-07100)
Drive in depth: 45.4 to 46.4 mm (1.7874 to 1.8268 inch)
b. Lightly apply MP grease to the tip of the oil seal.

NOTICE: Be careful not to damage the oil seal lip.

34. INSTALL REVERSE RESTRICT PIN ASSEMBLY
a. Install the reverse restrict pin into the transfer adapter.

b. Using a pin punch (5 mm) and a hammer, install the reverse restrict slotted pin into the transfer adapter.
c. Using a "Torx" socket wrench T40, install the reverse restrict pin plug onto the transfer adapter.
Torque: 18.5 Nm (189 kgf-cm, 14 ft. lbs.)

35. INSTALL OIL RECEIVER
a. Install the oil receiver onto the transfer adapter.

36. INSTALL TRANSFER ADAPTER
a. Apply seal packing to the transfer adapter as shown in the illustration.
Seal packing: Part No.08826-00090, THREE BOND 1281 or equivalent.

b. Using a plastic hammer, tap the transfer adapter to attach it to the transmission case.

c. Install the transfer adapter, onto the transmission case with the 10 bolts.
Torque: 37 Nm (380 kgf-cm, 27 ft. lbs.)

d. Install the shift lever housing set bolt.
Torque: 33 Nm (340 kgf-cm, 25 ft. lbs.)

37. INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY
a. Install the control shift lever retainer and transfer oil deflector onto the transfer adapter with the 4 bolts.
Torque: 18 Nm (185 kgf-cm, 13 ft. lbs.)

38. INSTALL REVERSE RESTRICT PIN ASSEMBLY
a. Install the 2 reverse restrict pins into the extension housing or transfer adapter.
Torque: 37 Nm (380 kgf-cm, 27 ft. lbs.)

39. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY
a. Using SST, install the back-up light switch assembly and the gasket onto the transmission case.
SST 09817-16011
Torque: 44 Nm (450 kgf-cm, 32 ft. lbs.)

40. INSTALL CLUTCH HOUSING
a. Install the clutch housing onto the transmission case with the 9 bolts.
Torque: 36 Nm (370 kgf-cm, 27 ft. lbs.)

41. INSTALL CLUTCH RELEASE FORK BOOT
a. Install the clutch release fork boot onto the clutch housing.

42. INSTALL RELEASE FORK SUPPORT
a. Install the clutch release fork support onto the clutch housing.
Torque: 47 Nm (480 kgf-cm, 35 ft. lbs.)

43. INSTALL CLUTCH RELEASE BEARING ASSEMBLY
a. Apply clutch release hub grease to the clutch release bearing, and install it onto the clutch release fork.

44. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY
a. Install the clutch release fork.
b. Apply the clutch spline grease to the spline of the input shaft.

45. INSTALL DRAIN PLUG SUB-ASSEMBLY
a. Install the drain plug onto the transmission case through a new gasket.
Torque: 37 Nm (380 kgf-cm, 27 ft. lbs.)

46. INSTALL MANUAL TRANSMISSION FILLER PLUG
a. Install the filler plug onto the transmission case through a new gasket.
Torque: 37 Nm (380 kgf-cm, 27 ft. lbs.)