Side Airbag Sensor (For Regular Cab)

Side Airbag Sensor (for Regular Cab):

SIDE AIRBAG SENSOR (for Regular Cab)

REMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTE:
- After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.
- Some systems need to be initialized after the cable is reconnected.

2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH (for Front Side)
3. REMOVE FRONT ARMREST BASE PANEL UPPER LH (for Front Side)
4. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (for Front Side)
5. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (for Front Side)
6. REMOVE COURTESY LIGHT ASSEMBLY (for Front Side)
7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (for Front Side)

8. REMOVE FRONT SIDE AIRBAG SENSOR
a. Disconnect the connector.
b. Remove the screw and side airbag sensor.

9. REMOVE FRONT DOOR SCUFF PLATE LH (for Rear Side)

10. REMOVE REAR SIDE AIRBAG SENSOR
a. Remove the bolt and side airbag sensor from the body.
b. Disconnect the connector.

INSTALLATION

1. INSTALL FRONT SIDE AIRBAG SENSOR
a. Check that the ignition switch is OFF.
b. Check that the cable is disconnected from the battery negative (-) terminal.

CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation

c. Install the door airbag sensor with the screw.

Torque: 9.0 N.m (92 kgf.cm, 80 in.lbf)

NOTE:
- If the door airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
- When installing the door airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

d. Check that there is no looseness in the installation parts of the side airbag sensor.
e. Connect the connector.

2. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (for Front Side)
3. INSTALL COURTESY LIGHT ASSEMBLY (for Front Side)
4. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH (for Front Side)
5. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (for Front Side)
6. INSTALL FRONT ARMREST BASE PANEL UPPER LH (for Front Side)
7. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH (for Front Side)

8. INSTALL REAR SIDE AIRBAG SENSOR
a. Check that the ignition switch is OFF.
b. Check that the cable is disconnected from the battery negative (-) terminal.

CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTE: Some systems need to be initialized after the cable is reconnected.

c. Install the side airbag sensor with the bolt.

Torque: 9.0 N.m (92 kgf.cm, 80 in.lbf)

NOTE:
- If the side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
- When installing the side airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

d. Check that there is no looseness in the installation parts of the side airbag sensor.
e. Connect the connector.

9. INSTALL FRONT DOOR SCUFF PLATE LH (for Rear Side)
10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTE: Some systems need to be initialized after the cable is reconnected.

11. CHECK SRS WARNING LIGHT
a. Check the SRS warning light.