Front Seat Assembly (For Power Seat)
FRONT SEAT ASSEMBLY (for Power Seat)Front Seat Assembly (for Power Seat):
Front Seat Assembly (for Power Seat):
Front Seat Assembly (for Power Seat):
REMOVAL
HINT:
- Use the same procedures for the LH side and RH side.
- The procedures listed below are for the LH side.
1. REMOVE FRONT SEAT HEADREST ASSEMBLY LH
2. REMOVE INNER FRONT SEAT TRACK COVER LH REAR
a. Operate the power seat switch to move the seat to the foremost position.
b. Using a screwdriver, detach the 2 claws and remove the seat track cover.
HINT: Tape the screwdriver tip before use.
3. REMOVE OUTER FRONT SEAT TRACK COVER LH REAR
a. Using a screwdriver, detach the 2 claws and remove the seat track cover.
HINT: Tape the screwdriver tip before use.
4. REMOVE FRONT SEAT ASSEMBLY LH
a. Operate the power seat switch to move the seat to the foremost position.
b. Remove the 2 bolts.
c. Operate the power seat switch to move the seat to the rearmost position.
d. Remove the 2 bolts.
e. Operate the power seat switch to move the seat to the center position.
f. w/ Leg Support Adjustment Switch:
Operate the leg support adjustment switch to move the seat cushion to the open position.
g. Disconnect the cable from the negative (-) battery terminal.
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
NOTICE:
- Some systems need to be initialized after the cable is reconnected.
- After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.
h. Disconnect the seat wire connectors under the seat.
i. Remove the front seat.
INSTALLATION
HINT:
- Use the same procedures for the LH side and RH side.
- The procedures listed below are for the LH side.
1. INSTALL FRONT SEAT ASSEMBLY LH
a. Install the front seat.
NOTICE: Be careful not to damage the vehicle body.
b. Connect the seat wire connectors under the seat.
c. Connect the cable to the negative (-) battery terminal.
NOTICE: Some systems need to be initialized after the cable is reconnected.
d. w/ Leg Support Adjustment Switch:
Operate the leg support adjustment switch to move the seat cushion to the closed position.
e. Operate the power seat switch to move the seat to the rearmost position.
f. Install the 2 bolts.
Torque: 37 N.m (377 kgf.cm, 27 ft.lbf)
g. Operate the power seat switch to move the seat to the foremost position.
h. Install the 2 bolts.
Torque: 37 N.m (377 kgf.cm, 27 ft.lbf)
2. INSTALL OUTER FRONT SEAT TRACK COVER LH REAR
a. Attach the 2 claws to install the seat track cover.
3. INSTALL INNER FRONT SEAT TRACK COVER LH REAR
a. Attach the 2 claws to install the seat track cover.
4. INSTALL FRONT SEAT HEADREST ASSEMBLY LH
5. CHECK SRS WARNING LIGHT
a. Check the SRS warning light.
6. INSPECT FRONT SEAT ASSEMBLY
a. Check the power seat operation.
b. w/ Seat Heater System:
Check the seat heater operation.
1. Turn the ignition switch ON.
2. When the seat heater switch is turned ON, check that the indicator light illuminates, and that the seat surface warms up in approximately 5 minutes.
3. When the seat heater switch's volume switch is operated, check that the seat surface temperature changes.