Check CAN Bus Line For Short to +B
CAN COMMUNICATION: CAN COMMUNICATION SYSTEM: Check CAN Bus Line for Short to +B
Check CAN Bus Line for Short to +B
DESCRIPTION
There may be a short circuit between the CAN bus line and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
- Turn the power switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
- After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If the doors need to be opened in order to check the connectors, open the doors and leave them open.
HINT:
- Operating the power switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.
PROCEDURE
1. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR CTR)
(a) Turn the power switch off, and disconnect negative battery terminal.
(b) Disconnect the CAN junction connector CTR.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Result:
D -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR RH)
C -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER MAIN WIRE)
B -- REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3
A -- Continue to next step.
2. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR CTR)
(a) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Result:
D -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
C -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
B -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)
A -- Continue to next step.
3. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR CTR)
(a) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Result:
C -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU BRANCH WIRE)
B -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU BRANCH WIRE)
A -- REPLACE CAN JUNCTION CONNECTOR CTR
4. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER MAIN WIRE)
(a) Disconnect the combination meter connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER MAIN WIRE)
OK -- REPLACE COMBINATION METER
5. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR RH)
(a) Disconnect the CAN junction connector RH.
(b) Measure the resistance according to the value(s) in the table below.
HINT: The resistance must be measured after the CAN junction connector CTR is disconnected.
Standard resistance:
Result:
C -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN JUNCTION CONNECTOR CTR - CAN JUNCTION CONNECTOR RH)
B -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (HYBRID VEHICLE CONTROL ECU MAIN WIRE)
A -- Continue to next step.
6. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR RH)
(a) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Result:
E -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
D -- CHECK SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)
C -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
B -- CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ACCESSORY GATEWAY BRANCH WIRE)
A -- REPLACE CAN JUNCTION CONNECTOR RH
7. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (HYBRID VEHICLE CONTROL ECU MAIN WIRE)
(a) Disconnect the hybrid vehicle control ECU connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (HYBRID VEHICLE CONTROL ECU MAIN WIRE)
OK -- REPLACE HYBRID VEHICLE CONTROL ECU
8. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)
(a) Disconnect the yaw rate sensor connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR BRANCH WIRE)
OK -- REPLACE YAW RATE SENSOR
9. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
(a) Disconnect the center airbag sensor assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
OK -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
10. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
(a) Disconnect the steering angle sensor connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR BRANCH WIRE)
OK -- REPLACE STEERING ANGLE SENSOR
11. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU BRANCH WIRE)
(a) Disconnect the power steering ECU connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU BRANCH WIRE)
OK -- REPLACE POWER STEERING ECU
12. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU BRANCH WIRE)
(a) Disconnect the main body ECU connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (MAIN BODY ECU BRANCH WIRE)
OK -- REPLACE MAIN BODY ECU
13. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
(a) Disconnect the air conditioning amplifier connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
OK -- REPLACE AIR CONDITIONING AMPLIFIER
14. CHECK SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)
(a) Disconnect the skid control ECU connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU BRANCH WIRE)
OK -- REPLACE SKID CONTROL ECU ASSEMBLY
15. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ACCESSORY GATEWAY BRANCH WIRE)
(a) Disconnect the accessory gateway connector.
HINT: If an accessory is not connected, repair or replace the accessory gateway branch wire or connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (ACCESSORY GATEWAY BRANCH WIRE)
OK -- CHECK AND REPLACE THE ACCESSORY
16. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
(a) Disconnect the navigation receiver assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
OK -- REPLACE NAVIGATION RECEIVER ASSEMBLY