Reassembly

ENGINE HOOD / DOOR: BACK DOOR: REASSEMBLY

REASSEMBLY

1. INSTALL CENTER STOP LIGHT ASSEMBLY (w/ Rear Spoiler) Installation
2. INSTALL CENTER STOP LIGHT ASSEMBLY (w/o Rear Spoiler)
3. INSTALL REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler) Installation
4. INSTALL BACK DOOR LOWER STOPPER CUSHION
(a) Install the lower stopper cushion with the 2 bolts.
Torque: 5.5 Nm (56 kgf-cm, 48 in-lbf)
5. INSTALL BACK DOOR STOPPER LOWER
(a) Install the stopper lower with the bolt.
Torque: 5.5 Nm (56 kgf-cm, 49 in-lbf)
6. INSTALL TELEVISION CAMERA ASSEMBLY (w/ Rear View Monitor System) Installation
7. INSTALL BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE
8. INSTALL BACK DOOR LOCK CYLINDER
(a) Install the lock cylinder with 2 the nuts.
Torque: 5.5 Nm (56 kgf-cm, 49 in-lbf)
(b) Install the tailgate control switch.
9. INSTALL REAR WIPER MOTOR ASSEMBLY
(a) Install the rear wiper motor assembly Installation.
(b) Install the liner wiper step LH.
10. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH REAR
HINT:
- To prevent the drum and cable from coming off, do not tilt the drum, subject it to shocks or use force on it.
- If the cable comes off the drum, do not rewind the cable and do not reuse it.
- After installing the window regulator, do not operate it by itself, because some types of regulator do not have a stopper.





(a) Apply MP grease to the as shown in the illustration.





(b) With the holding tool installed, match the holding tool with the motor housing.





(c) Push down on the wire guide and drum, and insert the drum into the motor housing.

NOTE: If you can not insert the drum into the motor, slowly slide the bracket for installing the glass, and insert the drum while aligning the drive shaft of the motor with the drum.





(d) Install the cover plate with the 2 screws.
Torque: 5.4 Nm (56 kgf-cm, 48 in-lbf)
(e) Install the window regulator motor with the window regulator.
11. INSTALL BACK DOOR POWER WINDOW REGULATOR SUB-ASSEMBLY





(a) Apply MP grease to the sliding and rotating parts of the window regulator.

NOTE: Do not apply grease to the spring of the window regulator.





(b) Install the power regulator sub-assembly with the 6 bolts, nut.
Torque: 8.0 Nm (82 kgf-cm, 71 in-lbf)
(c) Connect the window regulator connector.
(d) Install the 2 cushion rubbers.
12. INSTALL W/MOTOR BACK DOOR LOCK ASSEMBLY





(a) Install the door lock with 4 bolts.
Torque: 8.0 Nm (82 kgf-cm, 71 in-lbf)
(b) Connect the connector.
(c) Install the door lock protector.





(d) Install the 2 regulator control wires as shown in the illustration.
13. INSTALL BACK DOOR GLASS





(a) Insert the door glass as shown in the illustration.





(b) Install the door glass with the 4 bolts.
Torque: 8.0 Nm (82 kgf-cm, 71 in-lbf)
(c) Connect the rear window defogger connector.
14. INSTALL BACK DOOR GLASS RUN





(a) Install the door glass run.
(b) Check that the glass run position as shown in the illustration.
15. INSTALL BACK DOOR SERVICE HOLE COVER





(a) If replacing protector:
Install the protector, as shown in the illustration.
(b) Install the back door service hole cover with the 5 bolts.
(c) Install the multiplex network door ECU with the 2 bolts.
(d) Connect the multiplex network door ECU connector.
16. INSTALL BACK DOOR SERVICE HOLE COVER LH





(a) Apply butyl tape to the door.
Adhesive:
Part No. 08850-00065, Butyl Tape Set or equivalent
(b) Install the service hole cover, as shown in the illustration.

HINT:
- There should be no wrinkles or folds after attaching the service hole cover.
- After attaching the service hole cover, check the sealing condition.