Removal

BRAKE CONTROL: REAR SPEED SENSOR (for 4WD): REMOVAL

REMOVAL
HINT:
- Use the same procedures for the LH side and RH side.
- The following procedure is for the LH side.
- If the sensor rotor needs to be replaced, replace it together with the outboard joint shaft assembly.
Removal
Disassembly

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Repair Instruction - Initialization

2. REMOVE REAR DOOR SCUFF PLATE LH Removal
3. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH Removal
4. REMOVE DECK BOARD ASSEMBLY Removal
5. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY Removal
6. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY Removal
7. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) Removal
8. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat) Removal
9. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat) Removal
10. REMOVE DECK SIDE TRIM BOX LH Removal
11. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat) Removal
12. REMOVE JACK CARRIER SUPPORT
13. REMOVE JACK CARRIER CUSHION Removal
14. REMOVE JACK ASSEMBLY Removal
15. REMOVE JACK CARRIER ASSEMBLY Removal
16. REMOVE DECK SIDE TRIM BOX RH Removal
17. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat) Removal
18. REMOVE REAR MAT Removal
19. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat) Removal
20. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat) Removal
21. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat) Removal
22. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat) Removal
23. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat) Removal
24. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) Removal
25. REMOVE REAR FLOOR FINISH PLATE Removal
26. REMOVE DECK SIDE TRIM COVER LH Removal
27. REMOVE DECK SIDE TRIM LH Removal
28. REMOVE SIDE TRIM COVER LH (w/o Rear Seat Entertainment System) Removal
29. REMOVE POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System) Removal
30. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH Removal
31. REMOVE REAR POWER POINT SOCKET ASSEMBLY Removal
32. REMOVE REAR POWER OUTLET SOCKET COVER Removal
33. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function) Removal
34. REMOVE RECLINING REMOTE CONTROL BEZEL LH (w/ Remote Folding Function) Removal
35. REMOVE ROPE HOOK ASSEMBLY (for LH Side) Removal
36. REMOVE NO. 2 DECK SIDE TRIM HOOK Removal
37. REMOVE FRONT DECK SIDE TRIM COVER LH Removal
38. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH Removal
39. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH Removal
40. REMOVE REAR WHEEL
41. REMOVE REAR SPEED SENSOR





(a) Disconnect the rear speed sensor connector.





(b) Disconnect the grommet of the rear speed sensor wire from the hole of the wheel house.
(c) Remove the 2 bolts, No. 1 clamp and No. 2 clamp from the body and absorber.





(d) Remove the bolt and rear speed sensor body from the carrier.
NOTE: Keep the sensor tip and rear speed sensor installation hole free from foreign matter.