Reassembly

SEAT: REAR NO. 2 SEAT ASSEMBLY: REASSEMBLY

1. INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY

(a) Temporarily install the 2 bolts [C], 2 washers and the No. 2 seat cushion frame sub-assembly.

(b) Temporarily install the 2 bolts [B] and the 2 bushes.

(c) Temporarily install the 2 nuts, 2 bolts [A], 2 springs and the 2 E-rings.

(d) Tighten the 2 nuts, 2 bolts [B] and the 2 bolts [C] to install the No. 2 seat cushion frame sub-assembly.

Nut - Torque : 18 Nm (184 kgf-cm, 13 ft-lbf)

Bolt [B], Bolt [C] - Torque : 21 Nm (214 kgf-cm, 16 ft-lbf)

2. INSTALL NO. 1 REAR SEAT LOCK CABLE ASSEMBLY RH

(a) Connect the 2 cable clamps to install the No. 1 rear seat lock cable assembly RH.

3. INSTALL NO. 2 REAR SEAT CUSHION LOCK CABLE ASSEMBLY RH

(a) Connect the 2 cable clamps and install the No. 2 rear seat cushion lock cable assembly RH.

(b) Install a new clamp.

4. INSTALL NO. 1 REAR SEAT LOCK CABLE ASSEMBLY LH

(a) Connect the 2 cable clamps to install the No. 1 rear seat lock cable assembly LH.

5. INSTALL NO. 2 REAR SEAT CUSHION LOCK CABLE ASSEMBLY LH

(a) Connect the 2 cable clamps and install the No. 2 rear seat cushion lock cable assembly LH.

(b) Install a new clamp.

6. INSTALL REAR SEATBACK EDGE PROTECTOR

(a) Engage the 8 claws to install the 4 rear seatback edge protectors.

7. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY RH

(a) Install the rear No. 2 seat headrest assembly RH with the 3 nuts.

Torque : 14 Nm (143 kgf-cm, 10 ft-lbf)

(b) Connect the 2 cable clamps.

(c) Install the rear No. 2 seat headrest cover RH with the 2 screws.

8. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY LH

(a) Install the rear No. 2 seat headrest assembly LH with the 3 nuts.

Torque : 14 Nm (143 kgf-cm, 10 ft-lbf)

(b) Connect the 2 cable clamps.

(c) Install the rear No. 2 seat headrest cover LH with the 2 screws.

9. INSTALL NO. 2 REAR SEAT RECLINING COVER RH

(a) Engage the guide.

(b) Install the No. 2 rear seat reclining cover RH with the screw.

10. INSTALL NO. 2 REAR SEAT RECLINING COVER LH

(a) Engage the guide.

(b) Install the No. 2 rear seat reclining cover LH with the screw.

11. INSTALL REAR NO. 2 SEATBACK COVER SUB-ASSEMBLY

(a) Using hog ring pliers, install the rear No. 2 seatback cover sub-assembly with 18 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
12. INSTALL REAR NO. 2 SEATBACK COVER WITH PAD

(a) Temporarily install the rear No. 2 seatback cover with pad to the rear No. 2 seatback frame sub-assembly.

(b) Engage the 16 clips and install the rear No. 2 seatback cover.

(d) Using hog ring pliers, install the rear No. 2 seatback cover with pad with 4 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
13. INSTALL NO. 1 REAR SEAT COVER BEZEL

(a) Install the No. 1 rear seat cover bezel to the No. 1 rear side seat band sub-assembly.

(b) Engage the hook.

(c) Install the No. 1 rear seat cover bezel and the No. 1 rear side seat band sub-assembly with the 2 screws.

14. INSTALL NO. 2 SEATBACK BOARD SUB-ASSEMBLY

(a) Engage the 3 hooks.

(b) Engage the 7 clips to install the No. 2 seatback board sub-assembly.

15. INSTALL REAR NO. 2 SEAT HANDLE

(a) Connect the 2 cable clamps as shown in the illustration.

(b) Install a new clamp.

16. INSTALL REAR SEAT LOCK STRIKER COVER

(a) Engage the 2 guides.

(b) Engage the claw to install the rear seat lock striker cover.

17. INSTALL NO. 1 REAR SIDE SEAT BAND SUB-ASSEMBLY

(a) Attach the fastener.

(b) Install the seat track handle with the 2 new clips.

18. INSTALL REAR NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY

(a) Using hog ring pliers, install the rear No. 2 seat cushion cover sub-assembly with 14 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
19. INSTALL REAR NO. 2 SEAT CUSHION COVER WITH PAD

(a) Using hog ring pliers, install 4 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(b) Engage the 13 hooks to install the rear No. 2 seat cushion cover with pad.

20. INSTALL NO. 2 SEAT HINGE COVER RH

(a) Install the No. 2 seat hinge cover RH with the 2 screws.

21. INSTALL RECLINING COVER PROTECTOR RH

(a) Install the reclining cover protector RH with the 2 screws.

22. INSTALL NO. 2 SEAT HINGE COVER LH

(a) Install the No. 2 seat hinge cover LH with the 2 screws.

23. INSTALL RECLINING COVER PROTECTOR LH

(a) Install the reclining cover protector LH with the 2 screws.