Installation
INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: INSTALLATION
HINT
A bolt without a torque specification is shown in the standard bolt chart Standard Bolt - Specified Torque For Standard Bolts.
1. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
(a) Attach the 2 guides to install the instrument panel safety pad.
(b) Install the bracket with the 2 bolts and nut.
(c) Connect the connectors and attach the clamps and claws.
(d) Install the 2 passenger airbag bolts.
Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)
(e) Install the nut labeled A and bolt labeled B.
(f) Install the 6 bolts [E] and nut [F].
(g) Install the front floor carpet.
Text in Illustration
2. INSTALL MULTI-MEDIA INTERFACE ECU Installation
3. INSTALL FOUR WHEEL DRIVE CONTROL ECU (for 4WD)
(a) for VF2A:
Install the four wheel drive control ECU .
(b) for VF4BM:
Install the four wheel drive control ECU .
4. INSTALL DCM (TELEMATICS TRANSCEIVER) Installation
5. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY Installation
6. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
(a) Attach the 2 clips, 4 claws and 3 guides to install the No. 1 instrument panel speaker panel.
7. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
(a) Attach the 2 clips, 3 claws and 3 guides to install the No. 2 instrument panel speaker panel.
8. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
(a) Attach the 4 clips and 2 guides to install the No. 1 instrument panel register.
9. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
HINT
Use the same procedure described for the No. 1 instrument panel register.
10. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
(a) Connect each connector.
(b) Attach the 4 clips to install the lower center instrument cluster finish panel.
(c) Install the 2 screws [B].
11. INSTALL NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System) Installation
12. INSTALL RADIO RECEIVER ASSEMBLY (w/o Navigation System) Installation
13. INSTALL HEATER CONTROL ASSEMBLY Installation
14. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(a) Connect each connector.
(b) Attach the 10 clips to install the lower instrument panel.
(c) Install the 3 screws [B] and 2 bolts [C].
15. INSTALL INSTRUMENT PANEL BOX DOOR COVER
(a) Attach the 2 claws and 2 guides to install the instrument panel box door cover.
16. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY Installation
17. INSTALL LOWER INSTRUMENT COVER LH
(a) Attach the 4 claws to install the lower instrument cover.
18. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
(a) Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.
19. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY Installation
20. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
(a) Connect each connector and cable.
(b) Attach the 13 clips and 2 guides to install the lower instrument panel finish panel.
(c) Install the 2 bolts [C].
21. INSTALL COMBINATION METER ASSEMBLY Installation
22. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
(a) Attach the 7 clips to install the instrument cluster finish panel.
23. INSTALL NO. 2 SWITCH HOLE BASE
(a) Connect each connector.
(b) Attach the 6 clips and 2 guides to install the No. 2 switch hole base.
24. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
(a) w/o Smart Key System:
(1) Connect the cooler thermistor.
(2) Attach the 4 clips to install the lower instrument panel finish panel.
(b) w/ Smart Key System:
(1) Connect the connector and cooler thermistor.
(2) Attach the 4 clips to install the lower instrument panel finish panel.
25. INSTALL FRONT PILLAR GARNISH LH Installation
26. INSTALL FRONT PILLAR GARNISH RH Installation
27. INSTALL NO. 1 ASSIST GRIP Installation
28. INSTALL ASSIST GRIP PLUG Installation
29. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH Installation
30. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT
Use the same procedure described for the LH side.
31. INSTALL COWL SIDE TRIM BOARD LH Installation
32. INSTALL COWL SIDE TRIM BOARD RH
HINT
Use the same procedure described for the LH side.
33. INSTALL DOOR SCUFF PLATE ASSEMBLY LH Installation
34. INSTALL DOOR SCUFF PLATE ASSEMBLY RH
HINT
Use the same procedure described for the LH side.
35. INSTALL REAR CONSOLE BOX ASSEMBLY
(a) for 1GR-FE:
Install the rear console box assembly Installation.
(b) for 2TR-FE:
Install the rear console box assembly Installation.
36. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY
(a) Install the headlight dimmer switch assembly Installation.
37. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.
38. CHECK SRS WARNING LIGHT
(a) Check the SRS warning light Diagnosis System.