Part 2

INTERIOR: ROOF HEADLINING: INSTALLATION - Continued

33. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

(a) Engage the 5 claws to install the reclining remote control bezel LH.





34. INSTALL REAR POWER OUTLET SOCKET COVER Installation

35. INSTALL REAR POWER POINT SOCKET ASSEMBLY Installation

36. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH

(a) Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.





37. INSTALL SIDE TRIM COVER LH (w/o Rear Seat Entertainment System)

(a) Engage the 10 claws to install the side trim cover LH.





38. INSTALL POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)

(a) Connect each connector.





(b) Engage the 4 claws to install the power outlet socket bezel.





39. INSTALL DECK SIDE TRIM LH

(a) Engage the 3 guides and 4 claws as shown in the illustration.





(b) Install the deck side trim LH with the bolt.





40. INSTALL DECK SIDE TRIM COVER LH

(a) Engage the 2 claws to install the deck side trim cover LH.





41. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

42. INSTALL QUARTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

43. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

(a) Engage the 4 clips and the 7 claws.

(b) Install the 2 clips.

(c) Install the deck trim side panel assembly RH with the 3 bolts.





44. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

45. INSTALL FRONT DECK SIDE TRIM COVER RH

HINT
Use the same procedure for the RH side and the LH side.

46. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.

47. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

HINT
Use the same procedure for the RH side and the LH side.

48. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH

(a) Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.





49. INSTALL REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System) Installation

50. INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

(a) Engage the 4 claws to install the side trim cover RH.





51. INSTALL DECK SIDE TRIM RH

HINT
Use the same procedure for the RH side and the LH side.

52. INSTALL DECK SIDE TRIM COVER RH

HINT
Use the same procedure for the RH side and the LH side.

53. INSTALL REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)

(a) Engage the guide and the 8 claws, to install the rear seat side garnish cap.





54. INSTALL REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)

(a) Engage the guide and the 6 claws.





(b) Install the rear seat side garnish cap with the screw.

55. INSTALL REAR FLOOR FINISH PLATE

(a) Engage the 4 clips and the 4 claws, and install the rear floor finish plate.





56. INSTALL REAR NO. 2 SEAT ASSEMBLY Installation

57. INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY Installation

58. CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH Installation

59. CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH Installation

60. INSTALL NO. 1 DECK BOARD

(a) Engage the 3 clips and install the No. 1 deck board to the deck floor box.





61. INSTALL NO. 2 DECK BOARD

(a) Engage the 3 clips and install the No. 1 deck board to the deck floor box.





62. INSTALL REAR MAT

(a) Install the rear mat.





63. INSTALL DECK FLOOR BOARD ASSEMBLY

(a) Install the 2 nuts and the deck floor board assembly.





(b) Engage the 3 claws.

64. INSTALL DECK SIDE TRIM BOX LH

(a) Install the deck side trim box LH as shown in the illustration.





(b) Install the 2 deck side trim clips and clip.





65. INSTALL REAR SEAT SIDE COVER LH

(a) Engage the 2 clips and install the rear seat side cover LH.





66. INSTALL DECK SIDE TRIM BOX RH

(a) Install the deck side trim box RH as shown in the illustration.





(b) Install the 2 deck side trim clips and clip.





67. INSTALL JACK CARRIER ASSEMBLY

(a) Engage the 3 claws, and install the jack carrier assembly.





68. INSTALL JACK ASSEMBLY

(a) Install the jack assembly.





69. INSTALL JACK CARRIER CUSHION

(a) Install the jack carrier cushion.





70. INSTALL JACK CARRIER SUPPORT

71. INSTALL REAR SEAT SIDE COVER RH

(a) Engage the 2 clips and install the rear seat side cover RH.





72. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

(a) Install the tonneau cover assembly.

73. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

(a) Engage the 2 guides and install the No. 2 deck board sub-assembly.





74. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

(a) Engage the 2 guides and install the No. 3 deck board sub-assembly.





75. INSTALL DECK BOARD ASSEMBLY

(a) Install the deck board sub-assembly.





76. INSTALL CENTER PILLAR GARNISH LH

(a) Engage the 2 guides and the clip.





(b) Install the center pillar garnish LH with the clip and screw.

77. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH Installation

78. INSTALL LOWER CENTER PILLAR GARNISH LH

(a) Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.





79. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.





NOTICE:
After installation, check that the corners fit correctly.

80. INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.





81. INSTALL FRONT PILLAR GARNISH LH

(a) Remove the protective cover.





(b) Make sure that the front pillar garnish clip is not damaged.





NOTICE:
* If there is any damage, replace the garnish clip with a new one.
* When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

(c) Engage the 3 guides.

(d) Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

HINT
Tape the tips of the needle-nosed pliers before use.

(e) Engage the 2 clips to install the front pillar garnish LH.





82. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.





NOTICE:
After installation, check that the corners fit correctly.

83. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

(a) Engage the claw and clip, install the cowl side trim sub-assembly LH.





(b) Install the clip.

84. INSTALL FRONT DOOR SCUFF PLATE LH

(a) Engage the guide and the 8 claws, and install the front door scuff plate LH.





85. INSTALL CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

86. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

87. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

88. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.





NOTICE:
After installation, check that the corners fit correctly.

89. INSTALL REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

90. INSTALL FRONT PILLAR GARNISH RH

(a) Remove the protective cover.





(b) Make sure that the front pillar garnish clip is not damaged.





NOTICE:
* If there is any damage, replace the garnish clip with a new one.
* When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

(c) Engage the 3 guides.

(d) Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish RH.

HINT
Tape the tips of the needle-nosed pliers before use.

(e) Engage the 2 clips to install the front pillar garnish RH.





91. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.





NOTICE:
After installation, check that the corners fit correctly.

92. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

93. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

94. INSTALL REAR NO. 1 SEAT ASSEMBLY LH Installation

95. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function) Installation

96. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side) Installation

97. INSTALL REAR SEAT LEG SIDE COVER LH Installation

98. INSTALL REAR INNER TRACK BRACKET COVER LH Installation

99. INSTALL REAR OUTER TRACK BRACKET COVER LH Installation

100. INSTALL REAR SEAT TRACK BRACKET COVER LH Installation

101. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side) Installation

102. INSTALL REAR CENTER SEAT ASSEMBLY

103. INSTALL REAR NO. 1 SEAT ASSEMBLY RH Installation

104. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

HINT
Use the same procedure for the RH side and the LH side.

105. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side) Installation

106. INSTALL REAR SEAT LEG SIDE COVER RH Installation

107. INSTALL REAR INNER TRACK BRACKET COVER RH Installation

108. INSTALL REAR OUTER TRACK BRACKET COVER RH Installation

109. INSTALL REAR SEAT TRACK BRACKET COVER RH Installation

110. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side) Installation