Operation CHARM: Car repair manuals for everyone.
Home >> Toyota Truck >> 2011 >> Highlander 4WD V6-3.5L (2GR-FE) >> Repair and Diagnosis >> Body and Frame >> Seats >> Service and Repair >> Overhaul >> Rear No. 2 Seat Assembly >> Reassembly

Reassembly





SEAT: REAR NO. 2 SEAT ASSEMBLY: REASSEMBLY

1. INSTALL NO. 2 SEATBACK FRAME SUB-ASSEMBLY RH

(a) Install the 2 bolts.





Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)

(b) Install the No. 2 seatback frame sub-assembly RH with the 2 nuts.

Torque : 32 Nm (327 kgf-cm, 24 ft-lbf)

2. INSTALL REAR SEAT INNER SUSPENSION LINK SUB-ASSEMBLY RH

(a) Install the rear seat inner suspension link sub-assembly RH with the 2 nuts.





Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)

3. INSTALL REAR SEAT OUTER SUSPENSION LINK SUB-ASSEMBLY RH

(a) Engage the hook.





(b) Install the spring with the E-ring.

(c) Install the rear seat outer suspension link sub-assembly RH with the 2 nuts.





Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)

4. INSTALL REAR NO. 2 SIDE SEAT BAND SUB-ASSEMBLY RH

(a) Using an air riveter or a hand riveter, install the rear No. 2 side seat band sub-assembly RH.





Text in Illustration





NOTICE:
* Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
* Confirm that the rivet is seated properly against the seat frame. Do not tilt the riveter when installing the rivet to the seat frame. Do not leave any clearance between the rivet head and seat frame.
* Do not leave any clearance between the rear No. 2 side seat band sub-assembly RH and seat frame. Firmly hold the 2 items together while installing the rivet.

HINT
If the rivet cannot be cut, pull it once and cut it.

5. INSTALL REAR NO. 2 SEAT CUSHION LOCK CABLE ASSEMBLY RH

(a) Engage the 4 cable clamps to install the rear No. 2 seat lock cable assembly RH.





6. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH

(a) Engage the 2 cable clamps to install the rear No. 1 seat lock cable assembly RH.





7. INSTALL NO. 2 SEAT INNER HINGE COVER RH

(a) Engage the claw to install the No. 2 seat inner hinge cover RH.





8. INSTALL REAR NO. 2 SEAT RECLINING COVER RH

(a) Engage the 2 claws.





(b) Install the rear No. 2 seat reclining cover RH with the screw.

9. INSTALL NO. 2 SEAT HINGE COVER RH

(a) Engage the claw and guide.





(b) Install the No. 2 seat hinge cover RH with the screw.

10. INSTALL REAR NO. 2 SEAT LOWER CUSHION HINGE COVER RH

(a) Engage the 2 claws to install the rear No. 2 seat lower cushion hinge cover RH.





11. INSTALL REAR NO. 2 SEAT LOWER CUSHION HINGE COVER LH

(a) Engage the 2 claws to install the rear No. 2 seat lower cushion hinge cover LH.





12. INSTALL REAR SEAT BACK EDGE PROTECTOR RH

(a) Engage the 4 claws to install the 2 rear seatback edge protectors RH.





13. INSTALL NO. 2 SEAT HEADREST ASSEMBLY RH

(a) Install the No. 2 seat headrest assembly RH with the 3 nuts.





Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)

(b) Connect the 2 cable clamps.

14. INSTALL REAR SEAT HEADREST COVER RH

(a) Install the rear No. 2 seat headrest cover RH with the 2 screws.





15. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY RH

(a) Using hog ring pliers, install the No. 2 seatback cover sub-assembly RH to the No. 2 seatback pad sub-assembly RH with 9 new hog rings.





16. INSTALL NO. 2 SEATBACK COVER WITH PAD RH

(a) Engage the 8 clips.





(b) Install the rear No. 1 seat cover bezel RH to the rear side seat band sub-assembly RH.





(c) Engage the hook to install the rear side seat band sub-assembly RH as shown in the illustration.





(d) Install the rear No. 1 seat cover bezel RH with the 2 screws.

(e) Engage the hook.





(f) Engage the 13 hooks to install the No. 2 seatback cover with pad RH.





Text in Illustration





(g) Engage the fastener.

17. INSTALL NO. 2 SEATBACK BOARD SUB-ASSEMBLY RH

(a) Engage the 6 claws to install the No. 2 seatback board sub-assembly RH.





18. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH

(a) Using hog ring pliers, install 7 new hog rings.





(b) Engage the 3 hooks.





(c) Engage each hook.





(d) Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly with 2 new hog rings.





19. INSTALL REAR SEAT CUSHION COVER WITH PAD RH

(a) Install the 2 bolts.





Torque : 21 Nm (214 kgf-cm, 16 ft-lbf)

(b) Using a "T45" TORX socket wrench, install the rear seat cushion cover with pad RH with the 2 bolts and 2 bushes.





Torque : 32 Nm (326 kgf-cm, 24 ft-lbf)

20. INSTALL NO. 2 SEAT OUTER HINGE COVER RH

(a) Install the No. 2 seat outer hinge cover RH with the 2 screws.





21. INSTALL RECLINING COVER PROTECTOR RH

(a) Install the reclining cover protector RH with the 2 screws.





22. INSTALL NO. 2 SEATBACK FRAME SUB-ASSEMBLY LH

(a) Install the 2 nuts [C].





Torque : 32 Nm (326 kgf-cm, 24 ft-lbf)

(b) Install the bolt [B].

Torque : 32 Nm (326 kgf-cm, 24 ft-lbf)

(c) Install the No. 2 seatback frame sub-assembly LH with the 2 bolts [A].

Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)

23. INSTALL REAR SEAT INNER SUSPENSION LINK SUB-ASSEMBLY LH

(a) Install the rear seat inner suspension link sub-assembly LH with the 2 nuts.





24. INSTALL REAR SEAT OUTER SUSPENSION LINK SUB-ASSEMBLY LH

(a) Engage the hook.





(b) Install the spring with the E-ring.

(c) Install the rear seat outer suspension link sub-assembly LH with the 2 nuts.





Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)

25. INSTALL REAR NO. 2 SIDE SEAT BAND SUB-ASSEMBLY LH

(a) Using an air riveter or a hand riveter, install the rear No. 2 side seat band sub-assembly LH.





Text in Illustration





NOTICE:
* Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
* Confirm that the rivet is seated properly against the seat frame. Do not tilt the riveter when installing the rivet to the seat frame. Do not leave any clearance between the rivet head and seat frame.
* Do not leave any clearance between the rear No. 2 side seat band sub-assembly RH and seat frame. Firmly hold the 2 items together while installing the rivet.

HINT
If the rivet cannot be cut, pull it once and cut it.

26. INSTALL REAR NO. 2 SEAT CUSHION LOCK CABLE ASSEMBLY LH

(a) Engage the 4 cable clamps to install the rear No. 2 seat cushion lock cable assembly LH.





27. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH

(a) Engage the 2 cable clamps to install the rear No. 1 seat lock cable assembly LH.





28. INSTALL NO. 2 SEAT INNER HINGE COVER LH

(a) Engage the claw to install the No. 2 seat inner hinge cover LH.





29. INSTALL REAR NO. 2 SEAT INNER RECLINING COVER LH

(a) Engage the 2 claws.





(b) Install the rear No. 2 seat inner reclining cover LH with the screw.

30. INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER LH

(a) Engage the claw and guide.





(b) Install the rear No. 2 seat outer reclining cover LH with the screw.

31. INSTALL REAR NO. 1 SEAT LOWER CUSHION HINGE COVER RH

(a) Engage the 2 claws to install the rear No. 1 seat lower cushion hinge cover RH.





32. INSTALL REAR NO. 1 SEAT LOWER CUSHION HINGE COVER LH

(a) Engage the 2 claws to install the rear No. 1 seat lower cushion hinge cover LH.





33. INSTALL REAR SEATBACK EDGE PROTECTOR LH

(a) Engage the 4 claws to install the 2 rear seatback edge protectors LH.





34. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY LH

(a) Install the rear No. 2 seat headrest assembly LH with the 3 nuts.





Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)

(b) Engage the 2 cable clamps.

35. INSTALL REAR SEAT HEADREST COVER LH

(a) Install the rear seat headrest cover LH with the 2 screws.





36. INSTALL REAR NO. 2 SEATBACK COVER SUB-ASSEMBLY LH

(a) Using hog ring pliers, install the rear No. 2 seatback cover sub-assembly LH to the rear No. 2 seatback pad sub-assembly with 9 new hog rings.





37. INSTALL REAR NO. 2 SEATBACK COVER WITH PAD LH

(a) Engage the 8 clips to the rear No. 2 seat headrest assembly LH.





(b) Install the rear No. 1 seat cover bezel LH to the rear side seat band sub-assembly LH.





(c) Engage the hook as shown in the illustration to install the rear side seat band sub-assembly LH.





(d) Install the rear No. 1 seat cover bezel LH with the 2 screws.

(e) Engage the hook.





(f) Engage the 13 hooks to install the rear No. 2 seatback cover with pad LH.





Text in Illustration





(g) Engage the fastener.

38. INSTALL NO. 2 SEATBACK BOARD SUB-ASSEMBLY LH

(a) Engage the 6 claws to install the No. 2 seatback board sub-assembly LH.





39. INSTALL REAR NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH

(a) Using hog ring pliers, install 7 new hog rings.





(b) Engage the 3 hooks.





(c) Engage each hook.





(d) Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly LH with 2 new hog rings.





40. INSTALL REAR NO. 2 SEAT CUSHION COVER WITH PAD LH

(a) Install the 2 bolts.





Torque : 21 Nm (214 kgf-cm, 16 ft-lbf)

(b) Using a "T45" TORX socket wrench, install the rear No. 2 seat cushion cover with pad LH with the 2 bolts and 2 bushes.





Torque : 32 Nm (326 kgf-cm, 24 ft-lbf)

41. INSTALL NO. 2 SEAT OUTER HINGE COVER LH

(a) Install the No. 2 seat outer hinge cover LH with the 2 screws.





42. INSTALL RECLINING COVER PROTECTOR LH

(a) Install the reclining cover protector LH with the 2 screws.





43. INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER

(a) Engage the 2 clips.





(b) Install the rear No. 2 seat cushion hinge cover with the 2 screws.

44. INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY RH

(a) Install the rear No. 2 seat inner belt sub-assembly RH Installation.

HINT
Use the same procedure for the RH side and LH side.

pro multis · About Operation CHARM