Installation

SUSPENSION: REAR STABILIZER BAR (for 4WD): INSTALLATION

1. TEMPORARILY INSTALL REAR STABILIZER BAR

(a) Temporarily install the rear stabilizer bar with the identification mark positioned on the left side of the vehicle.





2. TEMPORARILY INSTALL REAR STABILIZER BAR BRACKET LH (for Front Side)

(a) Temporarily install the rear stabilizer bar bracket LH (front side) with the bolt.





HINT
Loosely tighten the bolt so that the bracket can be moved by hand.

3. TEMPORARILY INSTALL REAR STABILIZER BAR BRACKET RH (for Front Side)

(a) Temporarily install the rear stabilizer bar bracket RH (front side) with the 2 bolts.





HINT
Loosely tighten the bolts so that the bracket can be moved by hand.

4. INSTALL REAR STABILIZER BUSHING (for LH Side)

(a) Install the rear stabilizer bushing (LH side) to the rear stabilizer bar.





NOTICE:
Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration.

5. INSTALL REAR STABILIZER BUSHING (for RH Side)

(a) Install the rear stabilizer bushing (RH side) to the rear stabilizer bar.





NOTICE:
Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration.

6. INSTALL REAR STABILIZER BAR BRACKET LH (for Rear Side)

(a) Install the rear stabilizer bar bracket LH (rear side) with the 2 bolts.





Torque : 19 Nm (194 kgf-cm, 14 ft-lbf)

7. INSTALL REAR STABILIZER BAR BRACKET RH (for Rear Side)

(a) Install the rear stabilizer bar bracket RH (rear side) with the 2 bolts.





Torque : 19 Nm (194 kgf-cm, 14 ft-lbf)

8. FULLY TIGHTEN REAR STABILIZER BAR BRACKET LH (for Front Side)

(a) Fully tighten the bolt.





Torque : 54 Nm (550 kgf-cm, 40 ft-lbf)

9. FULLY TIGHTEN REAR STABILIZER BAR BRACKET RH (for Front Side)

(a) Fully tighten the 2 bolts.





Torque : 19 Nm (194 kgf-cm, 14 ft-lbf)

10. INSTALL REAR STABILIZER LINK ASSEMBLY LH

(a) Install the rear stabilizer link assembly LH to the rear shock absorber with coil spring LH with the nut.





Torque : 39 Nm (400 kgf-cm, 29 ft-lbf)

HINT
If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

(b) Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut.





Torque : 39 Nm (400 kgf-cm, 29 ft-lbf)

HINT
If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

11. INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT
Perform the same procedure as the LH side.

12. INSTALL TAIL EXHAUST PIPE ASSEMBLY Installation

13. INSPECT FOR EXHAUST GAS LEAK Installation

14. INSTALL REAR WHEELS

Torque : 103 Nm (1050 kgf-cm, 76 ft-lbf)

15. INSTALL SPARE WHEEL CARRIER LOCK COVER (w/ Cover)

16. INSTALL SPARE TIRE

17. INSTALL LOWER SPARE WHEEL CARRIER HINGE COVER (w/ Cover)

18. INSTALL DECK TRIM SERVICE HOLE COVER

19. INSTALL REAR MAT Installation

20. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) Installation

21. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover) Installation

22. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover) Installation

23. INSTALL DECK BOARD ASSEMBLY Installation