Installation
INSTRUMENT PANEL: INSTRUMENT PANEL SAFETY PAD: INSTALLATION
1. INSTALL NO. 2 CONSOLE BOX CUP HOLDER
(a) Install the No. 2 console box cup holder.
2. INSTALL INSTRUMENT PANEL CUP HOLDER ASSEMBLY
(a) Install the instrument panel cup holder assembly with the 4 screws [F].
3. INSTALL NO. 3 INSTRUMENT PANEL STAY
(a) Engage the claw and install the 5 No. 3 instrument panel stays.
4. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
(a) Engage the 5 claws.
NOTICE:
Do not allow the wire harness to get caught in the claws.
(b) Install the 2 bolts [D] and nut [G].
(c) Install the 2 clips.
(d) Engage each clamp.
(e) Install the 2 passenger airbag bolts [A].
Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)
(f) Connect each connector and install the instrument panel safety pad assembly.
5. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY Installation
6. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) Installation
7. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
(a) Engage the 2 guides.
(b) Engage the 2 claws and 2 clips, and install the No. 1 instrument panel speaker panel sub-assembly.
8. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
HINT
Use the same procedures for the RH side and the LH side.
9. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
(a) Engage the 2 guides.
(b) Engage the 2 claws and 2 clips, and install the No. 2 instrument panel speaker panel sub-assembly.
10. INSTALL FRONT PILLAR GARNISH RH Installation
11. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH Installation
12. INSTALL FRONT PILLAR GARNISH LH Installation
13. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH Installation
14. INSTALL POWER SWITCH (w/ Smart Key System) Installation
15. INSTALL FRONT NO. 2 CONSOLE BOX INSERT
(a) Engage the claw and 2 guides.
(b) Install the front No. 2 console box insert with the 3 screws [E] and clip.
16. INSTALL FRONT NO. 1 CONSOLE BOX INSERT
(a) Engage the claw and 2 guides.
(b) Install the front No. 1 console box insert with the 3 screws [E] and 2 clips.
17. INSTALL CONSOLE BOX ASSEMBLY Installation
18. INSTALL LOWER REAR CONSOLE BOX Installation
19. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
(a) Connect the connector.
(b) Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.
20. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(a) Connect each connector and clamp.
(b) Engage the 4 claws and 3 clips.
(c) Install the lower instrument panel sub-assembly with the 2 bolts [B] and 3 screws [E].
21. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
(a) Engage the 2 guides.
(b) Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.
22. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH Installation
23. INSTALL FRONT DOOR SCUFF PLATE RH Installation
24. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
(a) Connect the hood lock control cable assembly.
(b) for Automatic Air Conditioning System:
Connect the aspirator duct.
(c) Connect each connector.
(d) Engage the 3 claws and 10 clips.
(e) Install the lower instrument panel finish panel sub-assembly with the 2 bolts [B].
25. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH Installation
26. INSTALL FRONT DOOR SCUFF PLATE LH Installation
27. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System) Installation
28. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System) Installation
29. INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System) Installation
30. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System) Installation
31. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Key System)
(a) Apply protective tape to the areas shown in the illustration.
(b) Connect each connector.
(c) Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.
NOTICE:
Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.
32. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Key System)
(a) Apply protective tape to the areas shown in the illustration.
(b) Connect each connector.
(c) Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.
NOTICE:
Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.
33. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY
(a) Engage the 2 claws and 5 clips, and install the center instrument panel register assembly.
34. INSTALL COMBINATION METER ASSEMBLY
(a) Connect the connector.
(b) Install the combination meter assembly with the 4 screws [E].
35. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
(a) Engage the 4 claws and 4 clips, and install the instrument cluster finish panel assembly.
36. POSITION FRONT WHEELS STRAIGHT AHEAD
37. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY Installation
38. INSTALL STEERING COLUMN COVER Installation
39. ADJUST SPIRAL CABLE SUB-ASSEMBLY Installation
40. INSTALL STEERING WHEEL ASSEMBLY Installation
41. INSPECT STEERING WHEEL CENTER POINT
42. INSTALL STEERING PAD Installation
43. INSTALL LOWER NO. 2 STEERING WHEEL COVER Installation
44. INSTALL LOWER NO. 3 STEERING WHEEL COVER Installation
45. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.
46. INSTALL BATTERY SERVICE HOLE COVER ASSEMBLY Installation
47. INSTALL DECK BOARD ASSEMBLY Installation
48. INSPECT STEERING PAD Installation
49. INSPECT SRS WARNING LIGHT
Diagnosis System