Part 3

1UR-FE ENGINE CONTROL: SFI SYSTEM: P1603, P1605: Engine Stall History
P1605 - Rough Idling - Continued

51. CHECK FREEZE FRAME DATA

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored Freeze Frame Data.

Result

HINT
Even if the results are normal, the park/neutral position switch and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch and/or A/T system (refer to step 59).

C -- REPLACE MALFUNCTIONING PARTS

B -- CHECK AUTOMATIC TRANSMISSION SYSTEM

A -- INSPECT PARK/NEUTRAL POSITION SWITCH

52. CHECK FREEZE FRAME DATA

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored Freeze Frame Data.

Result

B -- CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)
A -- Continue to next step.

53. INSPECT MASS AIR FLOW METER

(a) Remove the mass air flow meter.

(b) Check for foreign matter in the air flow passage of the mass air flow meter.

Result

(c) Install the mass air flow meter.

HINT
Even if the results are normal, the mass air flow meter may have been malfunctioning. Continue this inspection procedure until step 58, and if there are no problems with other parts, replace the mass air flow meter (refer to step 59).

B -- CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)

A -- REPLACE MASS AIR FLOW METER Removal

54. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)

(a) Disconnect the injector connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Text in Illustration

(a) Disconnect the ignition coil with igniter connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Text in Illustration

HINT
* Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
* Make sure there is not an excessive amount of force applied to the wire harness.
* A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)

NG -- REPAIR POWER SOURCE CIRCUIT P0351
OK -- Continue to next step.

56. PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON and turn the Techstream on.

(c) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.

(d) When performing the Active Test, check for an operating sound from the fuel pump.

OK:

Result

HINT
* Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
* While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
* If the fuel pump operating noise is abnormal, proceed to step 57.

B -- CHECK FUEL SYSTEM
A -- Continue to next step.

57. INSPECT FUEL PUMP

(a) Inspect the fuel pump. Fuel Pump

NG -- REPLACE FUEL PUMP Removal

OK -- CHECK FUEL PUMP CONTROL SYSTEM Component Tests and General Diagnostics

58. CHECK FUEL SYSTEM

(a) Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result

B -- REPLACE MALFUNCTIONING PARTS

A -- REPAIR OR REPLACE FUEL SYSTEM

59. REPLACE MALFUNCTIONING PARTS

(a) If the malfunction could not be identified in steps 3 to 24, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

(b) If the malfunction could not be identified in steps 25 to 34, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

(c) If the malfunction could not be identified in steps 35 to 44, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

(d) If the malfunction could not be identified in steps 45 to 51, inspect and repair the part which is suspected to be malfunctioning according to the step where an inspection was performed.

(e) If the malfunction could not be identified in steps 52 to 58, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

HINT
Referring to the chart, inspect and repair or replace the part from the step where an inspection was performed.

NEXT -- Continue to next step.

60. CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.

NEXT -- Continue to next step.

61. PERFORM CONFIRMATION DRIVING PATTERN

(a) Check if engine stall symptoms are present.

HINT
If any engine stall symptoms are present, recheck for DTCs and freeze frame data and perform an inspection.

NG -- REPAIR OR REPLACE MALFUNCTIONING PARTS

OK -- END