Installation

STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION

1. INSTALL STEERING COLUMN ASSEMBLY





(a) Install the steering column assembly with the 2 nuts and bolt.

Torque : 21 Nm (210 kgf-cm, 16 ft-lbf)

(b) Connect each of the connectors to the steering column assembly.

(c) Connect the wire harness clamps to the steering column assembly.

CAUTION:
Use a shop rag to wipe any dirt off the installation plane and column body side.

NOTICE:
Be careful not to scratch or soil the installation plane of the steering column.

2. INSTALL NO.2 STEERING INTERMEDIATE SHAFT





(a) Align the matchmarks on the power steering gear and No. 2 steering intermediate shaft.

(b) Install the No. 2 steering intermediate shaft onto the steering gear box with bolt C.

Torque : 35 Nm (357 kgf-cm, 26 ft-lbf) for bolt C

3. INSTALL STEERING SLIDING YOKE

(a) Align the matchmarks on the steering column and steering sliding yoke.

(b) Install the steering sliding yoke onto the steering column assembly and slide it upward.

(c) Align the matchmarks on the intermediate shaft sub-assembly No. 2 and steering sliding yoke.

(d) Install the sliding yoke onto the intermediate shaft sub- assembly No. 2 with bolts A and B.

Torque : 35 Nm (357 kgf-cm, 26 ft-lbf) for bolt A, B

4. INSTALL NO.1 ENGINE UNDER COVER SUB-ASSEMBLY

(a) Install the No. 1 engine under cover sub-assembly with the 4 bolts.

Torque : 30 Nm (306 kgf-cm, 22 ft-lbf)

5. INSTALL STEERING COLUMN HOLE COVER





(a) Install the steering column hole cover with the 4 clips.

6. INSTALL LOWER INSTRUMENT PANEL LH Installation

7. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY Installation

8. INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) Installation

9. INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) Installation

10. INSTALL COWL SIDE TRIM BOARD LH (for Regular Cab) Installation

11. INSTALL COWL SIDE TRIM BOARD LH (for Access Cab) Installation

12. INSTALL COWL SIDE TRIM BOARD LH (for Double Cab) Installation

13. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab) Installation

14. INSTALL FRONT DOOR SCUFF PLATE LH (for Access Cab) Installation

15. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab) Installation

16. INSTALL FRONT FLOOR FOOTREST Installation

17. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY Installation

18. INSTALL SPIRAL CABLE SUB-ASSEMBLY Installation

19. INSTALL UPPER STEERING COLUMN COVER

(a) Engage the claw and then install the steering column cover upper.

20. INSTALL LOWER STEERING COLUMN COVER

(a) Engage the 2 claws.

(b) Install the steering column cover lower with the 2 screws.

21. INSTALL STEERING WHEEL ASSEMBLY

(a) Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

(b) Install the steering wheel assembly set nut.

Torque : 50 Nm (510 kgf-cm, 37 ft-lbf)

22. INSTALL STEERING PAD Installation

23. INSTALL NO.3 LOWER STEERING WHEEL COVER

(a) Engage the claw and install the No. 3 lower steering wheel cover onto the steering wheel assembly.

24. INSTALL NO.2 LOWER STEERING WHEEL COVER

(a) Engage the claw and install the No. 2 lower steering wheel cover onto the steering wheel assembly.

25. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque : 3.9 Nm (40 kgf-cm, 35 in-lbf)

27. INSPECT SRS WARNING LIGHT

Diagnosis System