Installation

WINDSHIELD / WINDOW GLASS: BACK WINDOW GLASS (for Regular Cab and Double Cab): INSTALLATION

1. INSTALL NO. 1 BACK WINDOW GLASS SPACER

(a) Install 2 new spacers onto the back window assembly as shown in the illustration.

2. INSTALL NO. 2 BACK WINDOW GLASS SPACER

(a) Install 2 new spacers onto the back window assembly as shown in the illustration.

3. INSTALL BACK WINDOW ASSEMBLY

(a) Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

NOTICE:
* Allow the primer to dry for 3 minutes or more.
* Do not apply primer to the adhesive.
* Throw away any leftover primer.
* Do not apply too much primer.

(b) Using a brush or sponge, apply Primer G to the contact surface of the back window.

HINT
If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

NOTICE:
* Allow the primer to dry for 3 minutes or more.
* Throw away any leftover primer.
* Do not apply too much primer.

(c) Apply adhesive to the back window.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent

(1) Cut off the tip of the cartridge nozzle as shown in the illustration below.

HINT
After cutting off the tip, use all adhesive within the time written in the table below.

Usage time frame:

(2) Load the sealer gun with the cartridge.

(3) Apply adhesive to the back window as shown in the illustration.

Standard:

(d) Using suction cups, position the glass so that the reference marks are aligned. Press it in gently along the rim.

NOTICE:
* Allow the primer coating to dry for 3 minutes or more.
* Check that the clips are attached to the vehicle body correctly.
* Check the clearance between the vehicle body and glass.

(e) Lightly press the front surface of the back window to ensure that the back window is securely fit to the vehicle body.

NOTICE:
Check that the spacers are attached to the vehicle body correctly.

(f) Using a scraper, remove any excess or protruding adhesive.

NOTICE:
Do not drive the vehicle within the time written in the table below.

Minimum time:

4. CHECK FOR LEAK AND REPAIR

(a) Conduct a leak test after the adhesive has completely hardened.

(b) Seal any leaks with auto glass sealer.

5. INSTALL UPPER OUTSIDE BACK WINDOW MOULDING (for Slide Type, for Power Slide Type)

(a) Clean the back window surface.

(1) Using a heat light, heat the back window surface.

(2) Remove the double-sided tape from the back window.

(3) Wipe off any tape adhesive residue with cleaner.

(b) If reusing the moulding:

Clean the moulding.

(1) Using a heat light, heat the moulding.

(2) Remove the double-sided tape from the moulding.

(3) Wipe off any tape adhesive residue with cleaner.

(4) Apply new double-sided tape to the moulding, as shown in the illustration.

(c) Install the moulding.

(1) Using a heat light, heat the back window and moulding.

(2) Remove the peeling paper.

(3) Attach the 3 clips to install the moulding.

7. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH

8. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING RH

HINT
Use the same procedures described for the LH side.

9. INSTALL ROOF HEADLINING ASSEMBLY

(a) for Regular Cab:

Install the roof headlining Installation.

(b) for Double Cab:

Install the roof headlining Installation.

10. INSTALL BACK DOOR GLASS CHANNEL (for Power Slide Type)

HINT
Perform these procedures only when replacing the back window glass.

(a) Using a brush or sponge, coat the application area of a new back window glass with Primer G.

Standard:

NOTICE:
* Allow the primer to dry for 3 minutes or more.
* Throw away any leftover primer.
* Do not apply too much primer.

HINT
If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

Using a brush or sponge, coat the application area of a new back door glass channel with Primer M.

NOTICE:
* Allow the primer to dry for 3 minutes or more.
* Throw away any leftover primer.
* Do not apply too much primer.

HINT
If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

(b) Apply adhesive to the back door glass channel.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent

(1) Cut off the tip of a cartridge nozzle.

HINT
After cutting off the tip, use all adhesive within the time written in the table below.

Usage Time Frame:

(2) Load a sealer gun with the cartridge.

(3) Apply adhesive to the back door glass channel as shown in the illustration.

(c) Install the back door glass as shown in the illustration.

Apply non-residue solvent to a clean cloth and wipe off any excess or protruding adhesive.

11. INSTALL BACK WINDOW GLASS WITH BACK DOOR GLASS CHANNEL (for Power Slide Type)

HINT
Perform these procedures only when replacing the back window glass.

(a) Insert the back window glass into the channel (arrow 1). Attach the upper part of the back window glass to the upper channel (arrow 2). Then slide the back window glass towards the RH side (arrow 3) so that the glass channel fits between the ribs to install the back window glass.

(b) Insert the seal into the bottom of the channel (arrow 4), and then slightly push the seal to the channel (arrow 5) to install it.

(c) Using a T10 "TORX" driver, install the stopper with the screw (illustration A).

12. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Power Slide Type)

(a) Using a T25 "TORX" socket, install the power window regulator motor to the base plate with the 3 screws.

Torque : 5.4 Nm (55 kgf-cm, 48 in-lbf)

13. INSTALL DOOR WINDOW REGULATOR BASE PLATE (for Power Slide Type)

(a) Install the door window regulator base plate with the 3 nuts in the order shown in the illustration.

Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)

14. INSTALL DOOR WINDOW REGULATOR CABLE SUB-ASSEMBLY (for Power Slide Type)

(a) Rotate the drum assembly counterclockwise to align it with the motor pivot pin, and then connect the motor drum assembly to the motor pivot pin.

NOTICE:
Do not rotate the drum assembly more than 45°.

Rotate the drum assembly clockwise to attach the claw and connect the datum pin.

(b) Install the 2 bolts in the order shown in the illustration.

Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)

(c) Insert the wires into the back window as shown in the illustration labeled A.

(d) Compress the springs to release the tension in the cables, connect the wire ends to the back window as shown in the illustration labeled B, Then release the springs to restore the tension.

NOTICE:

Insert the cables so that the caps are fully inserted into the stoppers as shown in the illustration.

HINT
Use the same procedure described for the LH side.

(e) Attach the 6 clips labeled C in the illustration.

15. INSTALL NO. 1 BACK PANEL SILENCER (for Power Slide Type)

(a) Install the No. 1 back panel silencer with the 4 clips.

16. INSTALL COAT HOOK Installation

17. INSTALL ROOM LIGHT ASSEMBLY (for Short Type Overhead Console Box) Installation

18. INSTALL ROOF CONSOLE BOX ASSEMBLY (for Long Type Overhead Console Box) Installation

19. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

(a) for Regular Cab:

Install the quarter trim panel Installation.

(b) for Double Cab:

Install the quarter trim panel Installation.

20. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

21. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH

(a) for Regular Cab:

Install the quarter trim panel Installation.

(b) for Double Cab:

Install the quarter trim panel Installation.

22. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

23. INSTALL LUGGAGE COMPARTMENT BOX RH (for Regular Cab) Installation

24. INSTALL LUGGAGE COMPARTMENT BOX LH (for Regular Cab) Installation

25. INSTALL UPPER BACK PANEL GARNISH (for Regular Cab) Installation

26. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab)

27. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab)

28. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab)

29. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab)

30. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab) Installation

31. INSTALL FRONT DOOR SCUFF PLATE RH (for Regular Cab) Installation

32. INSTALL REAR DOOR SCUFF PLATE LH (for Double Cab) Installation

33. INSTALL REAR DOOR SCUFF PLATE RH (for Double Cab) Installation

34. INSTALL REAR SEAT ASSEMBLY (for Double Cab)

(a) Install the rear seat Installation.

35. INSTALL FRONT SEAT ASSEMBLY (for Center Seat)

(a) Install the front seat Installation.

36. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)

(a) Install the front seat Installation.

37. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)

(a) Install the front seat Installation.