Electrical Equipment, Removing (Eurovan CV Camper)
Electrical Equipment, Removing (EuroVan CV Camper)
Removing Battery Charger - A10 -
CAUTION: Before working on any part of electrical system obtain radio code. Disconnect battery Ground (GND- strap.
- Remove stop - 1 - from rail.
CAUTION: Note safety measures
- Release catch - 2 - and pull bench forward in direction of travel.
- Pry off caps - arrows - and remove recessed screws from lower screen cover - 1 -.
- Press screen cover - 1 - downward and pull out toward center of vehicle.
- Pull plug - 1 - and - 2 - off Battery Charger - A10 -.
- Remove recessed screws - arrows - and remove Battery Charger - A10 -.
Auxiliary batteries -A1-, removing
CAUTION: Note safety measures.
- Pull bench forward in direction of travel.
- Remove upholstered top - 1 -, panel - 2 - and insert panel - 3 -.
- Remove screw - 4 -.
- Open flap - 1 - and remove
- Remove hex nuts - 1 - and remove brackets - 2 -.
- Lift out rear Auxiliary Battery - A1 - - 3 -, disconnect connections and insulate positive cable (B+).
- Remove hex bolts - 1 - and take off angle bracket - 2 -.
- Lift out front Auxiliary Battery - A1 - - 3 -, disconnect connections and insulate positive cable (B+).
110/220 V Exterior socket - U8 -, removing
CAUTION: Note safety measures.
- Remove recessed screws and pull out 110/220 V Exterior Socket - U8 - - 1 -.
- Disconnect 110/220 V connector - 2 - and remove 110/220 Exterior Socket - U8 - - 1 -.
Central electronic display - E153 -, removing
- Press auxiliary tool (e.g. dia. 2.5 mm mandrel) into mounting holes - arrows - to a depth of approx.20 mm and pull out Camper Central Electronic Display - 1 -.
- Pry out securing clip - arrow - and pull off connector.
Central electronic display - E153 -, replacing
- When installing replacement unit, adjust DIP switches on back to equipment on vehicle.
- Adjust with suitable implement (e.g. a ball-point pen) according to the following table:
Fluorescent light right - W8 - / fluorescent light left - W25 -, removing
- Remove plastic nuts - 1 -.
- Remove panel - 2 -.
- Remove recessed screws - arrows -.
- Remove lamp housing - 1 -.
- Disconnect 12 V connectors.
Fluorescent tubes, removing
- Remove plastic nuts- 1 -.
- Remove panel - 2 -.
- Loosen four group screws - 1 - and pull out fluorescent tubes - 2 - in direction of arrow.
Front interior light - W28 -, removing
- Pry out Front Interior Light - W28 - - 1 - and disconnect connector - arrow -.
Reading lamp, removing
- Remove recessed screws - arrows -.
- Pull cable and grommet out of hole until connectors are visible.
- Disconnect connectors - arrows -.
Refrigerator - I -, removing
- Remove Battery Charger - A10 -.
- Remove upholstered top - 1 -, panel - 2 - and insert panel - 3 -.
- Lift kitchenette cover - 1 -.
- Remove guide rail - 2 -.
- Open door of left side storage compartment - 3 - and remove.
- Raise refrigerator -I- lid - 1 -.
- Remove frame - 2 - (three recessed screws - arrows -).
- Remove recessed screws- 1 -.
- Pry off caps - 2 -, remove recessed screws and lift out screen cover - 3 - upward.
- Close refrigerator - I - - 1 - lid.
- Open clothes closet - 2 - flap and remove.
- Open refrigerator - 1 - lid.
- From inside clothes closet, pry off caps - 1 - (if applicable-, remove hex nuts - 2 -, remove washers - 3 - and press out saucer-head screws - 4 -.
- Remove recessed screws - 5 -, if necessary remove refrigerator lift support screws.
- Remove cover - 6 -.
- Remove recessed screws - arrows - and remove angle bracket - 1 -.
- Disconnect plug - 1 - on underside of refrigerator - I -.
- Remove hex bolts - arrows - from bottom of refrigerator - I -.
- Remove false bottom - 1 - from kitchenette left-side storage compartment.
- Remove cover - 2 - (six recessed screws - arrows -).
- Loosen screw clamps - 1 - and - 2 - and disconnect vent hoses from base connections.
- Pull out cover for cooking stove.
- Remove recessed screws - arrows -.
- Lift out refrigerator - I -.
Compressor/refrigerator - I - filter, removing
- Remove securing bolts - arrows - under vehicle floor.
- Remove cover- 1 -.
- Press springs together in direction of arrow, and remove.
- Remove filter- 1 -.
Reading lamp (high roof), removing
- Remove recessed screws - arrows -.
- Pull connector cable with connectors - 1 - and - 2 - carefully out of drill hole.
- Disconnect connectors - 1 - and - 2 -.