Programming and Relearning
Radio Frequency Remote Control, Programming Ignition Keys
NOTES:
- With the introduction of this generation of central locking it is possible to program additional functions. Functions and programming see "Radio Frequency Remote Control Functions" below.
- If a new or additional ignition keys are required they must be adapted (matched) to the control module.
- Adaptation must be performed for all ignition keys, including the existing ones.
- The number of keys already programmed will be displayed when "Adaptation" (matching) function 10 is selected.
- Adaptation can be interrupted with the -C- button on the VAG 1551.
Requirements:
- All ignition keys available. If no old ignition key is available contact authorized VW Dealer for "Lost key procedure".
- Key fob with covered secret number is available, if not contact authorized VW Dealer for "Establishing secret number".
- Insert mechanically programmed ignition key in ignition lock.
- Connect VAG 1551 scan tool. VAG 1551 Scan Tool Connecting
- Initiate On Board Diagnostic (OBD). On Board Diagnostic, Initiating Program
The adaptation shown here is only an example.
Indicated on display
Rapid data transfer HELP
Select function XX
- Press buttons -1- and -0- to select "Adaptation" function 10.
Indicated on display
Rapid data transfer Q
10 - Matching
- Press -Q- button to confirm input.
Indicated on display
Matching
Insert channel number XX
- Press buttons -0- and -0- (all keys are erased with channel number 00).
- Press -Q- button to confirm input.
NOTE: It is not possible to match a new or additional key(s) without erasing existing programmed key(s).
Indicated on display
Adaptation Q
Clear learned values?
- Press -Q- button to confirm input.
Indicated on display
Adaptation ->
Learned values cleared
- Press -> button.
Indicated on display
Rapid data transfer HELP
Select function XX
- Press buttons -1- and -0- to select "Adaptation" function 10.
Indicated on display
Rapid data transfer Q
10 - Adaptation
- Press -Q- button to confirm input.
Indicated on display
Adaptation
Insert channel number XX
- Press buttons -0- and -1- (all keys are programmed with channel number 01).
Indicated on display
Adaptation Q
Insert channel number 01
- Press -Q- button to confirm input.
Indicated on display
Channel 1 Matching 1 ->
Key 1 <-1 3->
The top line displays number of keys to be programmed (standard =1). Select number of keys with buttons -1- and -3-.
- Press -> button.
Indicated on display
Channel 1 Matching 1 ->
Enter matching value XXXXX
- Press -0- key four times and enter number of all ignition keys to be programmed, including existing key, (e.g. 00003); max. possible qty. 4.
- Press -Q- button to confirm input.
Indicated on display (number of radio frequency keys to be programmed)
Channel 1 Matching 3 Q
Key 3 <-1 3->
- Press -Q- button to confirm input.
Indicated on display
Channel 1 Matching 3 Q
Store changed value?
- Press -Q- button to confirm input.
Indicated on display
Channel 1 Matching 1 ->
Changed value is stored
- A button must be pressed once on each of the radio frequency keys to be programmed (in example above, 3 keys).
- Switch ignition off and remove ignition key.
- Perform functional check (e.g. 3) of radio frequency keys.
NOTES:
- Successful adaptation can be confirmed by Read Measuring Value Block (function 08), display group 009 or display group 013. Read Measuring Value Block (Function 08)
- All 3 keys can be programmed in one adaptation cycle.
- Adaptation of all keys (pressing a button) must occur within 15 seconds.
The matching of ignition keys is automatically completed when:
- Number of keys to be programmed is reached.
- A button of one of the keys to be programmed is pressed frequently.
- Permissible matching period of 15 seconds is exceeded (DTC is stored).
- Press buttons -0- and -2- to select "Check DTC Memory" function 02.
If there is no DTC stored, the matching of the keys has been successfully completed.
Radio Frequency Remote Control Functions
The various functions listed in the table can be called up and programmed to each ignition key in any combination by selecting the channel numbers 03 - 08.
The matching shown here is only an example.
Indicated on display
Rapid data transfer HELP
Select function XX
- Press buttons -1- and -0- to select "Adaptation" function 10.
Indicated on display
Rapid data transfer Q
10 - Matching
- Press -Q- button to confirm input.
Indicated on display
Matching
Insert channel number XX
- Press buttons -0- and -6- (channel number 06 switches the horn on or off when locking).
Indicated on display
Matching Q
Insert channel number 06
- Press -Q- button to confirm input.
Indicated on display
Channel 6 Matching 0 ->
lock Beep off <-1 3->
- Press -> button.
Indicated on display
Channel 6 Matching 0 ->
Enter matching value XXXXX
- Press -> button.
- Press -0- button four times and -1- button once (e.g. 00001).
Indicated on display
Channel 6 Matching 0 Q
Enter matching value 00001
- Press -Q- button to confirm input.
Indicated on display
Channel 6 Matching 1 ->
lock Beep on <-13->
- Press -Q- button to confirm input.
Indicated on display
Channel 6 Matching 1 Q
Store changed value?
- Press -Q- button to confirm input.
Indicated on display
Channel 6 Matching 1 ->
Changed value is stored
- Press -> button
Indicated on display
Rapid data transfer HELP
Select function XX
- Press buttons -0- and -6- to select End Output" function 06.
Indicated on display
Rapid data transfer Q
06 - End Output
- Press -Q- button to confirm input.
Indicated on display
Rapid data transfer HELP
Insert address word XX
- Switch ignition off.
- Disconnect scan tool from Data Link Connector (DLC).