A/T Controls - MIL ON/DTC 00281 Stored in Memory

Condition





01 07 17 Jan. 29, 2007, 2002393, Supersedes Technical Bulletin Group 01 number 99-10 dated June 1, 1999 due to inclusion into ElsaWeb and updated content.

Customer States MIL ON, DTC 00281 Road Speed Sender -G68- Stored in TCM DTC Memory
The Malfunction Indicator Light is illuminated and DTC 00281 Road Speed Sender -G68- is stored in Transmission Control Module (TCM) DTC memory. No obvious fault has been found with Road Speed Sender -G68-.

Tip: The Road Speed Sender -G68- will not effect the vehicle speedometer or cruise control operations.

Tip: If DTC 00297 Gearbox Speed Sender -G38- is stored in TCM memory, also install -G38- overlay harness as outlined in Technical Bulletin instance 2002394 (Customer States MIL ON, DTC 00297 Gearbox Speed Sender -G38- Stored in TCM DTC Memory).

Technical Background
Not Applicable.

Production Solution
Not Applicable.

Service
Install -G68- overlay harness Part No: 1C0971661A as follows:

Engine compartment harness covers, removing
- Obtain radio code and preset radio stations.
- Disconnect battery ground (GND) strap.
- Remove battery and battery tray (see Repair Manual Group 27).
- Remove air cleaner housing (see Repair Manual Group 24).
- Remove engine wiring harness covers.

Road Speed Sender -G68-, replacing and removing existing connector





- Locate Road Speed Sender -G68- and replace.
- Cut connector and wires from main harness (near taped section of harness).

Plenum covers, removing
Remove inner plenum panel covers as follows:





- Pull center cover -1- forward out of latch and remove from instrument panel (arrow).





- Remove screws -1-.





- Lift left plenum panel cover -1- and remove from clips at front and rear edge.
- Pull cover -1- toward center of vehicle and out of retainer in A-pillar to remove.
- Lift right plenum panel cover -2- and remove from clips at front and rear edge.
- Pull cover -2- toward center of vehicle and out of retainer in A-pillar to remove.
- Remove mounting bolts from left closeout panel -3- and right closeout panel -4- and pull panels upward out of plenum to remove.
- Remove both A-pillar trim pieces.
- Remove screws -6- to allow removal of center defroster duct -5- and end pieces -7-.
- Remove boot from defroster duct to center air distribution duct -arrow-.
- Remove center defroster duct.

The TCM is located in the plenum chamber center right.





- Inspect TCM ground (GND) connection (must not be loose or corroded and terminal must be crimped on wire correctly).

Overlay harness, installing





- Connect overlay harness to Road Speed Sender -G68-.
- Route overlay harness along existing harness to plenum opening. White dotted line indicates general routing.





- Lightly pull on engine/ transmission harness -arrow- at plenum to loosen harness plenum grommet.
- Route overlay harness along side of grommet into plenum area.
- Route overlay harness in plenum along existing harness to Transmission Control Module (TCM) connector.





- Disconnect multi-pin connector from TCM.
- Cut tie wrap at end of connector and remove cover from connector by depressing tab with small screwdriver while pushing cover in direction of -arrow-.





- Obtain appropriate pin removal tool from VAS 1978 wire harness repair kit.
- Locate cavity 65 of TCM connector (yellow wire) and remove terminal.
- Insert the yellow wire of overlay harness into cavity 65.
- Locate cavity 20 of TCM connector (white wire) and remove terminal.
- Insert the white wire of overlay harness into cavity 20.
- Locate cavity 43 of TCM connector (black wire) and remove terminal.
- Insert the black wire of overlay harness into cavity 43.
- Cut 3 wires (previously removed) as close as possible to the taped section of harness.
- Install cover using new tie wrap.
- Install multi-pin connector to TCM.
- Tie wrap overlay harness to existing harness in plenum and engine compartment as necessary to ensure routing and prevent rattles.
- Install defroster duct, boot and all plenum covers in reverse order of removal.
- Install engine wiring harness covers.
- Install air cleaner housing (see Repair Manual Group 24).
- Install battery and battery tray (see Repair Manual Group 27).

WARNING:
Ensure that there is no person inside the vehicle when connecting battery ground strap.

- Connect battery ground (GND) strap.
- Connect VAS 5051/5052 Scan Tool.
- Check all systems for stored DTC's.
- Erase any stored DTC's.
- After connecting battery, check vehicle equipment (radio code, clock, electric windows) as per Repair Manual and/or Owner's Manual.
- Program radio station presets.

Warranty
Information only.

Required Parts and Tools





Tip:
Part number(s) are for reference only. Always see ETKA for the latest part(s) information.