Selector Mechanism Disassembling and Assembling

Selector mechanism, disassembling and assembling

Note: Lubricate mounting points and contact surfaces with grease Part No. G 052 142 A2.





1. Selector lever handle
- Press sleeve -item 2- down and pull handle off upward.
2. Sleeve
- Locates in the selector lever handle
- Prevents selector lever handle from being pulled off
3. Cover
- With selector indicator
- Clipped into frame -item 7-
4. Cover strip
- Insert in frame -item 7-
5. Selector lever position display
- Printed circuit for selector lever position display (illumination) is held in position by clips
- Contacts for selector lever position face to selector lever contact springs -item 27-
- Secure connector with retainer -item 6- to frame -item 7-
- Insert fibre optic light guide and wiring to connector housing in the mountings on frame
- Connecting and disconnecting connector
6. Retainer
- Clip push in housing into frame -item 7-
7. Frame
- Carefully pry off in corners
- Push in cover strip -item 4-
- Note position of printed circuits and wiring -item 5-
- When installing do not damage contact springs -item 27- for selector lever position display
8. Bolt, 7 Nm
- For locating spring -item- 12 and plate -item 11- to frame
9. Shim
10. Locking segment
- Place on centralizing elements of selector lever housing -item 16-
11. Plate
12. Locating spring with roller
- Locates in the detent in selector lever -item 13-
13. Selector lever
- With pull rod, spring, detent, contact spring for selector lever position and releasing locking cable
14. Roller
15. Circlip
16. Selector lever housing
- Need not be removed to replace the majority of individual parts, with the exception of selector lever and selector lever lock solenoid
17. Fulcrum pin
- Splined
- Grease shank
- Do not turn when installing selector lever
18. Bolt, 25 Nm
19. Locking lever
- For locking cable
- For locking in selector lever position p
20. Shim
21. Bolt
22. Gasket
- Always replace
23. Cover
- For selector lever housing
24. Bolt
- Qty. 14
25. O-ring
- Always replace
26. Bolt, 8 Nm
- Qty. 2
27. Contact spring
- For selector lever position display
28. Bolt, 4 Nm
- Place selector lever in to loosen and tighten
29. Clip
30. Steering lock
31. Bolt
- Qty. 2
- Solenoid to selector lever housing
32. Shift lock solenoid -N110-
- Removing and installing
- Can be checked in electrical test and in measured value block
- Only remove and install with selector lever in position "1"
- Note positions of spring and locking pin when removing
- Remove together with locking pin and spring, and when doing this move selector lever back and forth slightly
- Route wiring with sufficient clearance to selector lever
33. Cable tie
- Wiring/solenoid to selector lever housing
- Always replace
34. Spring
35. Locking pin
36. Nut, 13 Nm
- Always replace
37. Washer
38. Nut, 25 Nm
- Qty. 2
- Always replace
39. Locking cable
- For ignition key removal lock
- Must not be kinked
- Checking operation of the ignition key withdrawal lock.
40. Circlip
- Always replace
- For mounting selector lever cable to selector lever housing
- Install with angled end inside selector housing
41. Gasket
- Always replace
42. Selector lever cable
- Do not bend or kink
- If the outer cable is damaged the selector lever cable must be renewed
- Lightly grease ball socket and cable ends before installing
43. Lever
- For selector shaft
44. Support bracket
- For mounting selector lever cable or transmission
45. Circlip
- Always replace