Throttle Valve Control Module, Adaptation to ECM
Throttle Valve Control Module, Adapting to Engine Control Module
The adaption teaches the engine control module the various positions of the throttle module when the ignition is switched on and the engine is not running. These positions are stored in the control module. The feedback of the throttle valve position is via both angle senders for throttle valve drive.
Adapting sequence must be performed if:
- The throttle valve control module is removed and installed
- The throttle valve control module is replaced
- If when installing another engine another throttle valve control module is installed
- The engine control module is replaced.
NOTE: On vehicles fitted with an automatic transmission the transmission control module must also be adapted:
Special tools and equipment required
Adapting sequence must be performed if:
- The throttle valve control module is removed and installed
- The throttle valve control module is replaced
- If when installing another engine another throttle valve control module is installed
- The engine control module is replaced.
NOTE: On vehicles fitted with an automatic transmission the transmission control module must also be adapted:
Special tools and equipment
- Scan tool VAG 1551 or vehicle system tester VAG 1552 with cable VAG 1551/3
Test conditions
- No faults must be stored in fault memory, interrogating fault memory. Refer to "Displaying, Reading and Erasing Trouble Codes" Testing and Inspection - The battery voltage must be at least 11.5 V.
- The throttle valve must be at idling speed position (The accelerator must not be operated during the test).
- The throttle valve part must not be dirty (carbonization).
- Coolant temperature must be 5-95 °C See display group 04, display zone 3.
- The cruise control system must be functioning correctly if installed.
Work sequence
- Connect the scan tool VAG 1551 (VAG 1552). Then switch ignition on and select engine control module with the "Address word" 01.
(Connecting scan tool and selecting engine control module). Refer to "VAG 1551 Scan Tool" [1][2][3][4][5]Connecting VAG 1551 Scan Tool
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press keys 0 and 4 for the function "Introduction of basic setting" and confirm entry with Q key.
Indicated on display:
Basic setting HELP
Input display group number XXX
- Press keys 0, 6 and 0 for the "Display group number 60" and confirm entry with Q key.
Indicated on display: (1-4 = display zones)
Basic setting 60 ->
xxx % xxx % x ADP.runs
After pressing the Q key the throttle valve positioner is switched so that it is not supplied with voltage at start of test.
In this condition the throttle valve is pulled into an emergency running position by a mechanical spring in the throttle valve control module. The values that both angle senders provide in the emergency running position are stored by the engine control module.
Thereafter the throttle valve is opened a predetermined value. If this value is achieved, the throttle valve is again switched so that it is not supplied with voltage. Now the mechanical spring must pull the throttle valve to the previously learned emergency running position within a predetermined period (spring test).
Then the throttle valve is closed by the throttle valve positioner and the values, which are supplied by the angle senders in the throttle valve control module are stored by the engine control module.
If the engine control module switches the throttle valve positioner so that it is without voltage during normal operation, this is indicated by the increased and hunting idling speed. The engine reacts slowly to accelerator changes.
Indicated on display: (1-4 = display zones)
Basic setting 60 ->
xxx % xxx % 8 ADP.OK.
Adapting has been performed successfully.
- End the engine basic setting by pressing the -> key.
- Press keys 0 and 6 for the function "End output" and confirm entry with the Q key.
To store the values:
- Switch off ignition.
NOTE: If the basic setting of the control module is interrupted, the cause could be one of the following:
- The test conditions were not fulfilled.
- Throttle valve control module or wiring is defective. Check Testing and Inspection .
After an interruption a fault is stored in fault memory. When next switching on ignition the basic setting is automatically performed again.