4 Speed Automatic 01M
Electrical/Electronic Components, Locations
1 - Transmission Control Module (TCM) -J217-
- Checked by On Board Diagnostic (OBD).
2 - Engine Control Module (ECM)
NOTE: If the engine or transmission control modules are replaced, the system must be returned to basic setting.
3 - Data Link Connector (DLC)
4 - Valve body
- The solenoid valves -N88-, -N89-, -N90-, - N91-, -N92-, -N93- and -N94- are attached to the valve body
- The valves are checked by On Board Diagnostic (OBD)
5 - Conductor strip with integrated Transmission Fluid Temperature Sensor -G93-
- -G93- is checked by On Board Diagnostic (OBD)
6 - Multi-function Transmission Range (TR) Switch -F125-
- -F125- is checked by On Board Diagnostic (OBD)
7 - Transmission Vehicle Speed (VSS) Sensor - G38-
- -G38- is checked by On Board Diagnostic (OBD)
8 - Vehicle Speed Sensor (VSS) -G68-
- -G68- is checked by On Board Diagnostic (OBD)
9 - Throttle Position (TP) Sensor -G69-
- Signal of -G69- is checked by On Board Diagnostic (OBD)
10 - Shift Lock Solenoid -N110-
- The solenoid is checked by On Board Diagnostic (OBD)
- Can be checked electrically and via reading measured value block
11 - Transmission Range (TR) Selector Lever Display -Y5-
12 - Cruise Control Switch - E45-
- Can be checked via reading measured value block.
13 - Kick Down Switch -F8-
- Can be checked electrically and via reading measured value block.
14 - Brake Light Switch -F-
- Can be checked electrically and via reading measured value block.
15 - Park/Neutral Position (PNP) Relay -J226-
4 Speed Automatic 01M
Electrical/Electronic component locations
1. Automatic transmission control module-J217
- see Fig. 1
2. Engine control module
- see Fig. 2
3. Data Link Connector (DLC)
- see Fig. 3
4. Valve body
5. Conductor strip with integrated Transmission fluid temperature sensor G93
6. Multifunction transmission range (TR) switch -F125
7. Transmission vehicle speed sender-G38
8. Vehicle speed sensor -G68
9. Throttle position (TP) sensor -G69
- see Fig. 4
10. Shift lock solenoid -N110
11. Transmission range selector lever display -Y5
- see Fig. 5
12. Cruise control switch -E45
- see Fig. 6
13. Kickdown switch -F8
- see Fig. 7
14. Brake light switch -F
- see Fig. 8
15. Park/Neutral position (PNP) relay-J226
- see Fig. 9
Fig. 1 Transmission control module -arrow- located in plenum chamber middle/right.
Removing control module
- Switch ignition off, open hood.
- Remove wiper arms and cowl panel:
- Release multi-pin connector and pull connector off control module.
- Remove screws -arrows-.
- Remove control module.
Installing control module
Installation is performed in the reverse order of removal.
- Locate multi-pin connector on control module -J217 pins (arrows) then lock multi-pin connector.
Fig. 2 Engine control module
Location: The control module is located in plenum chamber.
Fig. 3 Data Link Connector (DLC)
Location: The DLC -arrow- is located behind the cover above the ashtray.
Fig. 4 Throttle position (TP) sensor-G69
Locations:
On vehicles with a gasoline engine the sensor is a component part of the throttle valve control module -J338-. It can be found on the throttle valve housing (engine).
On a vehicles with a Diesel engine the "Throttle valve signal" is generated in the Throttle position (TP) sensor -G79-. The sensor can be found near the accelerator pedal.
On vehicles with data bus, the signal comes from the bus. On these vehicles, the data bus interface is checked in addition.
Fig. 5 Transmission range (TR) selector lever display -Y5
Location: The selector lever position display is located in the instrument cluster.
Removing and installing TR selector lever display.
Fig. 6 Cruise control switch -E45
Location: Cruise control switch is located on steering column switch.
Removing and installing cruise control switch
Fig. 7 Kickdown switch -F8-
Locations:
The kickdown switch (arrow) is integrated into accelerator cable and is located on bulkhead in engine compartment.
On vehicles which do not have an accelerator cable the kickdown signal is generated in the Throttle position (TP) sensor -G79-. The sensor can be found close to the accelerator pedal.
On vehicles with data bus, the signal comes from the bus. On these vehicles, the data bus interface is checked in addition.
Removing and installing kickdown switch
On a gasoline engine the accelerator cable must be removed to be able to remove and install the kickdown switch. The cable must be readjusted.
Fig. 8 Brake light switch -F-
Location: Brake light switch (arrow) is located on the pedal cluster.
Removing and installing brake light switch
Fig. 9 Park/Neutral Position (PNP) relay -J226-
Location: Relay located on additional relay carrier under the instrument panel, left.
The relay is marked with the number "175" -arrow-.