Replacement Instrument Cluster, Adaptation (Function 10)
Replacement Instrument Cluster, Adaptation (function 10)
NOTE:
- If the 4-digit secret number is not known or the new vehicle key fob with the secret number is not available, the secret number must be requested from the corporate radio/immobilizer code retrieval system by supplying the 14-character immobilizer control module identification number.
- If only the instrument cluster is being replaced, the secret number of the old instrument cluster must be used for adaptation. If all components are being replaced, use the secret number of the new instrument cluster.
- Every instrument cluster has its own secret number!
Requirements
Authorized key available.
- Insert old (authorized) key into ignition lock.
- Connect VAG 1551 Scan Tool (ST), switch on ignition, select operating mode 1 "Rapid data transfer" and enter address word 17 for "instrument cluster".
Indicated on display (example only):
1J0920905K COMBI + IMMOBIL. VDO X07 ->
Coding 21115 WSC 00000
r Upper line Part number of control module 3), System identification (Instrument cluster), Manufacturer code:VDO = VDO version number
r Bottom line Coding number 1), Work Shop Code 2)
1) Dependent on engine, transmission and optional equipment
2) Automatically stored in the control module upon entry into the installed system, except where a control modules was previously installed in another vehicle.
- Press -> button.
Indicated on display (example only):
XXXXXXXXXXXXXXXXX VWZ1Z0Y0371425 ->
r Upper line Vehicle Identification Number (VIN), (17-digit, WVW....identification number, (14-digit, VW....)
With new immobilizer control modules, place holders are indicated instead of the Vehicle Identification Number (VIN) before adaptation.
- Press -> button.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press buttons -1- and -0- to select "Adaptation", function 10.
Indicated on display:
Rapid data transfer Q
10 - Adaptation
- Press -Q- button to confirm input.
Indicated on display:
Adaptation
Enter channel number XX
- Press buttons -5- and -0- to select "channel 50".
- Press -Q- button to confirm input.
Indicated on display:
Channel 50 adaptation 32000 ->
PIN ?
- Press -> button.
Indicated on display:
Channel 50 adaptation 32000 Q
Enter adaptation value XXXXX
- Input the secret number, place a -0- before the 4 digit number (e.g. 01915).
- Press -Q- button to confirm input.
NOTE:
If displayed:
Function is unknown or can ->
not be performed at the moment
- Secret number not accepted. Repeat input.
- 3 attempts at entering the secret number correctly are possible immediately. The next 3 attempts are not permitted for at least 10 minutes. During this time, the ignition must remain switched on. On Board Diagnostic (OBD) must be also exited using the "End Output" function 06.
- The waiting period between each of the next 3 attempts doubles up to the maximum time of 255 minutes.
Indicated on display:
Channel 50 Adaptation 32000
<-1 3->
Indicated on display:
Channel 50 Adaptation 32000
Wait
Indicated on display (example only):
Channel 50 Adaptation 32000 Q
WVWZZZ3BZ1W0000273
After successful adaptation, Vehicle Identification Number (VIN) is indicated in the lower line of the display.
- Press -Q- button to confirm input.
Indicated on display:
Channel 50 Adaptation 32000 Q
Store changed value?
- Press -Q- button to confirm input.
Indicated on display:
Channel 50 Adaptation 32000 ->
Changed value is stored
- Press -> button.
- Press -Q- button to confirm input.
- Press -> button until "Select function" appears in display.
Indicated on display
Rapid data transfer HELP
Select function XX
- Press button -1- twice to select "Login" function 11.
Indicated on display
Rapid data transfer Q
11 - Login procedure
- Press -Q- button to confirm input.
Indicated on display
Login procedure Q
Enter code number XXXX
- Where applicable, read secret number located on the new vehicle key fob (visible by carefully "scratching off" protective coating, e.g. with a coin).
NOTE:
- If the 4-digit secret number is not known or the new vehicle key fob with the secret number is not available, the secret number must be requested from the corporate radio/immobilizer code retrieval system by supplying the 14-character immobilizer control module identification number.
- Using VAG 1551 button pad, enter secret number (when doing so, insert 0 before 4 digit number, example: 01915).
- Press -Q- button to confirm input.
Indicated on display
Rapid data transfer HELP
Select function XX
If this appears on display, secret number is not accepted:
Tester sends address word 17
- Enter secret number again.
NOTE:
- Three attempts to enter secret number are immediately possible. The next three attempts are only possible after a minimum of 10 minutes (if the ignition remains switched on during this time and OBD program is exited via the function 06 "End Output").
- Waiting period between each three attempts doubles each time up to a maximum of 255 minutes.
- Press buttons -1- and -0- to select "Adaptation" function 10.
Indicated on display
Rapid data transfer Q
10 - Adaptation
- Confirm entry with -Q- button.
Indicated on display
Adaptation
Enter channel number XX
- Press buttons -2- and -1- to select "Channel 21".
- Press -Q- button to confirm input.
If this appears on display
Function is unknown or ->
cannot be carried out at the moment
- Repeat adaptation function and secret number.
Indicated on display
Channel 21.........Adaptation 2 ->
<-1 3->
The top line of the display shows that 2 ignition keys are adapted to the system.
- Press -> button.
Indicated on display
Channel 21........Adaptation 2 ->
Enter adaption value XXXXX
- Press button -0- four times and then enter the total number of all ignition buttons to be adapted, including existing key (e.g.: for a total of three ignition keys, enter "00003"); max. possible Qty.: 8.
- Press -Q- button to confirm input.
Indicated on display for 3 ignition keys to be adapted
Channel 21 Adaptation 3 Q
<-1 3->
- Press -Q- button to confirm input.
Indicated on display
Channel 21 Adaptation 3 Q
Store changed value?
- Press -Q- button to confirm input.
Indicated on display
Channel 21 Adaptation 3 ->
Changed value is stored
VDO instrument clusters:
Warning light for anti-theft immobilizer -K117- goes out.
The key in the ignition/starter lock is now adapted.
- Press -> button.
- Switch ignition off and remove key.
- Insert next key in ignition/starter lock and switch ignition on again.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Switch off ignition.
- Switch ignition on again within 60 seconds.
- Adapt all ignition keys.