Shift Mechanism (Layout), Disassembling and Assembling
Shift mechanism (layout), disassembling and assembling, 01V, 5 SPD. A/T (FWD)
Sequence for disassembling and assembling
Lubricate mounting and sliding surfaces with Polyurea grease Part No. G 052 142 A2.
1. Selector lever handle
^ Removing and installing
2. Sleeve
^ Clips into selector lever handle
^ Installation position: Angled section faces inward
3. Cover
^ With trim piece -6-, symbol panel -7-, cover strip -8- and guide -9-
^ Lift up to remove
^ Removing connector for selector lever lock and Tiptronic
4. Guide sleeve
^ Slide onto selector lever -14-
^ Installation position: Engage foot to rear
5. Cover molding
^ With trim piece -6- and symbol panel -7-
^ Cannot be replaced as single item
6. Trim piece
^ Integrated in symbol panel -7- in cover molding -5-
^ Cannot be replaced as single item
7. Symbol panel
^ With printed circuit
^ With Tiptronic switch -F189- integrated in printed circuit
^ Integrated in trim piece -6- in cover molding -5-
^ Cannot be replaced as single item
8. Cover strip
^ With 2 solenoids for Tiptronic switch -F189- and gear indicator
^ Solenoids must be fitted securely on cover strip
^ Removing and installing
9. Guide
^ Guides masking panel
^ Unclipping from cover molding -5-.
10. Mounting bushing
^ Secure in mounting bracket -22- with locking clip -11-
11. Locking plate
^ Secures mounting bushing -10- in mounting bracket -22-
^ Install with angled ends pointing toward inside of mounting bracket
12. Pull rod
13. Spring
14. Selector lever
^ With pull rod, coil spring, selector gate and Tiptronic spring mechanism
15. Stop buffer
^ Clip into cable lever -17-
^ Install with large contact surface toward selector lever
16. Detent
^ Clip into cable lever -17-
17. Cable lever
^ Secured in mounting bracket -22- with fulcrum pin -23-
18. Spring clip with roller
^ For gearshift positions
19. Spring clip with roller
^ For Tiptronic position
20. Frame
^ Clip onto mounting bracket
^ Install with ribbed side upward
21. Nut, 10 Nm
22. Mounting bracket
23. Fulcrum pin
^ Secures cable lever -17- in mounting bracket -22-
24. Locking pawl
^ For selector lever lock
25. Shift lock solenoid -N110-
^ Removing and installing wire for selector lever lock
^ Can be checked using "guided fault finding" with the VAS 5051
26. Fulcrum pin
27. Cover
^ With seal for mounting bracket
28. Nut, 10 Nm
29. Securing clip
^ Secures selector lever cable to cable lever -17-
^ Install with angled end forward and upward
30. Locking plate
^ Secures selector lever cable to mounting bracket
^ Angled ends points to end of selector lever cable
31. Selector lever cable
^ Do not bend or kink, lightly grease cable eye and ball socket before installing.
^ Selector lever cable must be replaced if rubber sleeves are damaged
^ When installing, make sure that rubber sleeve on transmission side is not twisted
32. Hex bolt, 23 Nm
33. Support bracket
34. Bracket
35. Cable clip
36. Ignition/starter switch
37. Locking cable
^ For ignition key removal lock
^ Must not be kinked
^ Adjusting
38. Locking cable lever
^ For ignition key removal lock
39. Securing spring
^ For locking cable
40. Mounting
^ For selector lever in Tiptronic position
Removing and installing wiring for selector lever lock, selector lever illumination and Tiptronic
Removing
- Remove center console and extension.
- Unplug connector -1- for selector lever lock magnet -2- (concealed).
- Unclip cover -3- and lift up.
- Pull out connector -4- for gearshift positions and Tiptronic in direction of arrow.
Installing
Installation is performed in the reverse order.