Selector Mechanism, Disassembling and Assembling
Selector mechanism, disassembling and assembling, 01M, 4 Spd. A/T
Note: Lubricate mounting points and contact surfaces with grease Part No. G 052 142 A2.
1 - Selector lever handle
^ Press sleeve item -2- down and pull handle off upward.
2 - Sleeve
^ Locates in selector lever handle
^ Prevents selector lever handle from being pulled off
3 - Cover
^ With selector indicator
^ Clipped into frame item -7-
4 - Cover strip
^ Insert in frame item -7-
5 - Selector lever position display
^ Printed circuit for selector lever position display (illumination) is held in position by clips
^ Contacts for selector lever position face to selector lever contact springs item -27-
^ Secure connector with retainer item -6- to frame item -7-
^ Insert fiber optic light guide and wiring to connector housing in mountings on frame
^ Connecting and disconnecting connector
6 - Retainer
^ Clip push-in housing into frame item -7-
7 - Frame
^ Carefully pry off in the corners
^ Push in cover strip item -4-
^ Pay attention to position of printed circuits and wiring item -5-
^ When installing do not damage contact springs item -27- for selector lever display
8 - Bolt
^ 7 Nm
^ Locating spring item -12- and plate item -11- to frame
9 - Shim
10 - Locking segment
^ Place on centralizing elements of selector lever housing item -16-
11 - Plate
12 - Locating spring with roller
^ Locates in the detent in selector lever item -13-
13 - Selector lever
^ With pull rod, spring, detent, contact spring for selector lever position and releasing locking cable
14 - Roller
^ For releasing locking cable
15 - Circlip
16 - Selector lever housing
^ Need not be removed to replace majority of individual parts, with exception of selector lever and shift lock solenoid
17 - Fulcrum pin
^ Splined
^ Grease shank
^ Do not turn when installing selector lever
18 - Bolt
^ 25 Nm
19 - Locking lever
^ For locking cable
^ For locking in selector lever position "P"
20 - Shim
21 - Bolt
22 -Gasket
^ Always replace
23 - Cover
^ For selector lever housing
24 - Bolt
^ Qty. 14
25 - O-ring
^ Always replace
26 - Bolt
^ 8 Nm
^ Qty. 2
27 - Contact spring
^ For selector lever display
28 - Bolt
^ 4 Nm
^ Place selector lever in "P" to loosen and tighten
29 - Clip
30 - Steering lock
31 - Bolt
^ Qty. 2
^ Solenoid to selector lever housing
32 - Shift lock solenoid -N110-
^ Only remove and install with selector lever in position "1"
^ Pay attention to spring and locking pin when removing
^ Remove together with locking pin and spring. When doing this move selector lever back and forth slightly
^ Route wiring with sufficient clearance to selector lever
33 - Cable tie
^ Wiring/solenoid to selector lever housing
^ Always replace
34 - Spring
35 - Locking pin
36 - Nut
^ 13 Nm
^ Always replace
37 - Washer
38 - Nut
^ 25 Nm
^ Qty. 2
39 - Locking cable
^ For ignition key removal lock
^ Must not be kinked
^ Checking operation of the ignition key withdrawal lock.
40 - Circlip
^ Always replace
^ For mounting selector lever cable to selector lever housing
^ Install with angled end inside selector housing
41 - Gasket
^ Always replace
42 - Selector lever cable
^ Do not bend or kink
^ If the outer cable is damaged the selector lever cable must be replaced
^ Lightly grease ball socket and cable ends before installing
43 - Lever
^ For selector shaft
44 - Support bracket
^ For mounting selector lever cable on transmission
45 - Circlip
^ Always replace