Antenna and Sensors For Access/Start Authorization
Antenna And Sensors For Access/Start Authorization
Antenna And Sensors For Access/Start Authorization - Assembly Overview
The illustration depicts component locations in the Passat Sedan. In the Passat Wagon, the component locations of the individual components are identical. Component is discontinued in the wagon.
1 - Comfort System Central Control Module J393
- Component location: behind glove compartment on front passengers side
- Replacing/coding Comfort System Central Control Module J393
2 - Passengers side outside door handle
The following components are integrated in passengers side outside door handle:
- Front Passengers Outside Door Handle Touch Sensor G416
- Right access/start authorization antenna R135
Removing and installing passenger-side outside door handle
- Checking Right Access/Start Authorization Antenna R135
3 - Right rear outside door handle
The following components are integrated in right rear outside door handle:
- Proximity sensor
- Locking sensor right rear outside door handle
- Checking Right Rear Outside Door handle Touch Sensor G418
4 - Interior Access/Start Authorization Antenna 3 R154
NOTE: The Interior Access/Start Authorization Antenna 3 R154 is installed in the Passat Sedan only and has been discontinued in the wagon.
- Sedan location: Below rear shelf
- Checking Interior Access/Start Authorization Antenna 3 R154
5 - Access/Start Authorization Antenna (in rear bumper) R136
- Component location: behind rear bumper cover
- Checking Access/Start Authorization Antenna (in rear bumper) R136
6 - Luggage Compartment Access/Start Authorization Antenna R137
- Component location: in luggage compartment, center, in front of spare wheel well
- Checking Luggage Compartment Access/Start Authorization Antenna R137
7 - Rear left outer door handle
The following components are integrated in left rear outside door handle:
- Proximity sensor
- Locking sensor left rear outside door handle
- Checking Left Rear Outside Door Handle Touch Sensor G417
8 - Drivers side outside door handle
The following components are integrated in drivers side outside door handle:
- Drivers Outside Door Handle Touch Sensor G415
- Left access/start authorization antenna R134 driver-side outside door handle
- Checking Drivers Outside Door Handle Touch Sensor G415
- Checking Left Access/Start Authorization Antenna R134
9 - Interior Access/Start Authorization Antenna 2 R139
- Component location: on center tunnel at rear, in front of rear seat bench heel panel
- Checking Interior Access/Start Authorization Antenna 2 R139
10 - Interior Access/Start Authorization Antenna 1 R138
- Component location: on center tunnel, between front seats
- Checking Interior Access/Start Authorization Antenna 1 R138
Driver-side outside door handle, removing and installing
The following components are integrated in drivers side outside door handle:
- Drivers Outside Door Handle Touch Sensor G415
- Left access/start authorization antenna R134
NOTE:
- The complete outer door handle must always be replaced if malfunctioning.
- No coding, basic setting or adaptation is necessary when outside door handle is replaced. Erase any DTC entries in DTC memory via "Guided Fault Finding" using Vehicle Diagnosis, Testing and Information system VAS 5051A or.
Removing:
- Switch off ignition and all electrical components and move ignition key or start button into position 0 (preliminary engaged position).
- Remove left front outside door handle.
Installing:
Install in reverse order of removal.
Passenger-side outside door handle, removing and installing
The following components are integrated in passengers side outside door handle:
- Front Passengers Outside Door Handle Touch Sensor G416
- Right access/start authorization antenna R135
NOTE:
- The complete outer door handle must always be replaced if malfunctioning.
- No coding, basic setting or adaptation is necessary when outside door handle is replaced. Erase any DTC entries in DTC memory via "Guided Fault Finding" using Vehicle Diagnosis, Testing and Information system VAS 5051A or.
Removing:
- Switch off ignition and all electrical components and move ignition key or start button into position 0 (preliminary engaged position).
- Remove right front outside door handle.
Installing:
Install in reverse order of removal.
Left rear outside door handle, removing and installing
The following components are integrated in left rear outside door handle:
- Left access/start authorization antenna R134
NOTE:
- The complete outer door handle must always be replaced if malfunctioning.
- No coding, basic setting or adaptation is necessary when outside door handle is replaced. Erase any DTC entries in DTC memory via "Guided Fault Finding" using Vehicle Diagnosis, Testing and Information system VAS 5051A.
Removing:
- Switch off ignition and all electrical components and move ignition key or start button into position 0 (preliminary engaged position).
- Remove left rear outside door handle.
Installing:
Install in reverse order of removal.
Right rear outside door handle, removing and installing
The following components are integrated in right rear outside door handle:
- Right access/start authorization antenna R135
NOTE:
- The complete outer door handle must always be replaced if malfunctioning.
- No coding, basic setting or adaptation is necessary when outside door handle is replaced. Erase any DTC entries in DTC memory via "Guided Fault Finding" using Vehicle Diagnosis, Testing and Information system VAS 5051A.
Removing:
- Switch off ignition and all electrical components and move ignition key or start button into position 0 (preliminary engaged position).
- Remove right rear outside door handle.
Installing:
Install in reverse order of removal.
Access/Start Authorization Antenna (in rear bumper) R136, removing and installing
Component location of Access/Start Authorization Antenna (in rear bumper) R136 is behind the rear bumper cover.
NOTE: No coding, basic setting or adaptation is necessary if Access/Start Authorization Antenna (in rear bumper) R136 is replaced. Erase any DTC entries in DTC memory via "Guided Fault Finding" using Vehicle Diagnosis, Testing and Information system VAS 5051A.
Removing:
- Switch off ignition and all electrical components and move ignition key or start button into position 0 (preliminary engaged position).
- Remove rear bumper cover.
- Disengage Access/Start Authorization Antenna (in rear bumper) R136 -1- from lower section of bumper, paying attention to lengths of connected wires.
- Disengage and disconnect harness connector -2- and remove Access/Start Authorization Antenna (in rear bumper) R136 -1- from vehicle.
Installing:
Install in reverse order of removal, noting the following:
- Connect harness connector -2- to the Access/Start Authorization Antenna (in rear bumper) R136 -1- until it engages.
- Insert Access/Start Authorization Antenna (in rear bumper) R136 -1- first into mount in bumper base and then press it into its end position until it engages.
Interior Access/Start Authorization Antenna 1 R138, removing and installing
Component location of Interior Access/Start Authorization Antenna 1 R138 is beneath center console at front, between front seats.
NOTE: No coding, basic setting or adaptation is necessary if Interior Access/Start Authorization Antenna 1 R138 is replaced. Erase any DTC entries in DTC memory via "Guided Fault Finding" using Vehicle Diagnosis, Testing and Information system VAS 5051A.
Removing:
NOTE: The alignment and exact position of the antennas are crucial for their function. Before removing antennas in the passenger compartment, mark the exact position and alignment of antennas and secure them in exactly these positions and alignments when installing. The thickness of the adhesive pad layer on antennas is an integral part of their function. If the bond of one antenna loosens, do not reapply standard adhesive on it. In this case, a new antenna must be installed with a new adhesive pad. If this is not done, the KESSY system will malfunction.
- Switch off ignition and all electrical components and move ignition key or start button into position 0 (preliminary engaged position).
- Remove center console.
NOTE: For reasons of clarity, vehicle floor carpet is not depicted in the illustration.
- Disengage and disconnect harness connector -2- and remove adhesive of Interior Access/Start Authorization Antenna 1 R138 -1-.
- Remove Interior Access/Start Authorization Antenna 1 R138 -1- from vehicle.
Installing:
Install in reverse order of removal, noting the following:
- Place connector -2- in Interior Access/Start Authorization Antenna 1 R138 -1- until it engages.
- Bond the Interior Access/Start Authorization Antenna 1 R138 on to center console in the position and alignment marked during removal.
Interior Access/Start Authorization Antenna 2 R139, removing and installing
Component location of Interior Access/Start Authorization Antenna 2 R139 is on center console at rear, in front of rear seat bench heel panel.
NOTE: No coding, basic setting or adaptation is necessary if Interior Access/Start Authorization Antenna 2 R139 is replaced. Erase any DTC entries in DTC memory via "Guided Fault Finding" using Vehicle Diagnosis, Testing and Information system VAS 5051A.
Removing:
NOTE: The alignment and exact position of the antennas are crucial for their function. Before removing antennas in the passenger compartment, mark the exact position and alignment of antennas and secure them in exactly these positions and alignments when installing. The thickness of the adhesive pad layer on antennas is an integral part of their function. If the bond of one antenna loosens, do not reapply standard adhesive on it. In this case, a new antenna must be installed with a new adhesive pad. If this is not done, the KESSY system will malfunction.
- Switch off ignition and all electrical components and move ignition key or start button into position 0 (preliminary engaged position).
- Remove rear seats.
- Remove rear sill panel trim far enough until vehicle floor carpet can be folded forward sufficiently to gain access to Interior Access/Start Authorization Antenna 2 R139.
NOTE: For reasons of clarity, vehicle floor carpet and foam piece are not depicted in the illustration.
- Disengage and disconnect harness connector -2- and remove adhesive of Interior Access/Start Authorization Antenna 2 R139 -1-.
- Remove Interior Access/Start Authorization Antenna 2 R139 -1- from vehicle.
Installing:
Install in reverse order of removal, noting the following:
- Insert harness connector -3- into Interior Access/Start Authorization Antenna 2 R139 -2 - until it engages.
- Push Interior Access/Start Authorization Antenna 2 R139 into foam piece -1-.
- Align foam piece -1- together with antenna at wiring -2- on center console.
- Bond Interior Access/Start Authorization Antenna 2 R139 on to center tunnel.
Interior Access/Start Authorization Antenna 3 R154, removing and installing
Component location of Interior Access/Start Authorization Antenna 3 R154 is beneath rear shelf, in vicinity of rear window roller shade.
NOTE: No coding, basic setting or adaptation is necessary if Interior Access/Start Authorization Antenna 3 R154 is replaced. Erase any DTC entries in DTC memory via "Guided Fault Finding" using Vehicle Diagnosis, Testing and Information system VAS 5051A.
Luggage Compartment Access/Start Authorization Antenna R137, removing and installing
Component location of Luggage Compartment Access/Start Authorization Antenna R137 is in luggage compartment, at center in front of spare wheel well.
NOTE: No coding, basic setting or adaptation is necessary if Luggage Compartment Access/Start Authorization Antenna R137 is replaced. Erase any DTC entries in DTC memory via "Guided Fault Finding" using Vehicle Diagnosis, Testing and Information system VAS 5051A.
Removing:
NOTE: The alignment and exact position of the antennas are crucial for their function. Before removing antennas in the passenger compartment, mark the exact position and alignment of antennas and secure them in exactly these positions and alignments when installing. The thickness of the adhesive pad layer on antennas is an integral part of their function. If the bond of one antenna loosens, do not reapply standard adhesive on it. In this case, a new antenna must be installed with a new adhesive pad. If this is not done, the KESSY system will malfunction.
- Switch off ignition and all electrical components and move ignition key or start button into position 0 (preliminary engaged position).
- Remove cargo area floor.
- Disengage and disconnect harness connector -2- and remove adhesive of Luggage Compartment Access/Start Authorization Antenna R137 -1-.
- Remove Luggage Compartment Access/Start Authorization Antenna R137 -1- from vehicle.
Installing:
Install in reverse order of removal, noting the following:
- Before bonding, align antenna at both markings -arrows- on edge of spare wheel well.
- Bond on the Luggage Compartment Access/Start Authorization Antenna R137 within these markings so that lower edge of antenna housing lies 4-5 mm above upper edge of spare wheel well edge.