Mode 6 Data

Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions

Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.

The values of the individual test results must reach the specified value or must be within the min. and max. limits.

• Depending on scan tool and protocol used, the information in Diagnostic Mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).

Test requirements

• Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.

• No DTCs stored in the DTC memory.

• Coolant temperature at least 80° C.

Work procedure

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

- Select the desired "Test-ID" of the component or system that is to be monitored, e.g. "Test-ID 01: Oxygen Sensor Monitor Bank 1 - Sensor 1".

- Select the desired "Test-ID".

The current minimum and maximum values will be displayed on the scan tool screen.

The following table is a numerical list of all"Test-IDs" or " Hex-IDs" that may be selected.





OBDMID 01 ($01): Oxygen Sensor Monitor Bank 1 - Sensor 1

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 01 ($01) ".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 02 ($02): Oxygen Sensor Monitor Bank 1- Sensor 2

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 02 ($02)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 03 ($03): O2 Sensor Monitor, (Bank 1, Sensor 3)

- Connect the scan tool.

- Start engine and let it run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

- Select "OBDMID 03 ($03): Catalytic converter monitoring".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 33 ($21): Catalytic Converter Monitoring Bank 1

- Connect the scan tool.

- Start engine and let it run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

- Select "OBDMID ($21): Catalytic converter monitoring".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 59 ($3B): Fuel Tank EVAP System Leak Test (0.040/1.0 mm)

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 59 ($3B)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID Test-ID 60 ($3C): Fuel Tank EVAP System Leak Test (0.020 /0.5 mm)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 60 ($3C)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID Test-ID 61 ($3D): Tank Vent Valve - Function Check

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 61 ($3D)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 65 ($41): Oxygen Sensor Heating in front of Catalytic Convertor ( Bank 1 - Sensor 1)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 65 ($41)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 66 ($42)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

OBDMID 67 ($43): Oxygen Sensor Heater Monitor (Bank 1 - Sensor 3)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 67 ($43)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 113 ($71): Secondary Air System (Bank 1 )

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 113 ($71)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 162 ($A2): Combustion Misfire Cylinder 1 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 162 ($A2)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 163 ($A3): Combustion Misfire Cylinder 2 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 163 ($A3):".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 164 ($A4): Combustion Misfire Cylinder 3 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 164 ($A4)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 165 ($A5): Combustion Misfire Cylinder 4 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 165 ($A5)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.

OBDMID 166 ($A65): Combustion Misfire Cylinder 5 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Diagnostic Mode 06 - Check Test Results of Components that are not Continuously Monitored".

Select "OBDMID 165 ($A5)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values, refer to "Diagnostic Mode 03 - Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

End of Diagnosis.