HID Headlamps with Cornering Lamp Assembly Overview, from 12.06
HID Headlamps with Cornering Lamp Assembly Overview, from 12.06
• After performing work which can affect headlamp adjustment, check headlamp adjustment and adjust headlamps if necessary.
1 - Screws
• For mounting left/right HID lamp control modules to headlamp housing.
2 - Left High-intensity Gas Discharge Lamp Control Module (J343) and Right High-intensity Gas Discharge Lamp Control Module (J344)
• Left High-intensity Gas Discharge Lamp Control Module (J343) and Right High-intensity Gas Discharge Lamp Control Module (J344) is not capable of On Board Diagnostic (OBD).
• Removing and installing --> [ HID Headlamp Control Module ] HID Headlamps with Cornering Lamp, from 12.06
3 - Bolt
• for mounting left or right headlamp power output module on bracket.
4 - Left Headlamp Power Output Stage (J667) or Right Headlamp Power Output Stage (J668)
• Removing and installing --> [ Headlamp Power Output Stages ] HID Headlamps with Cornering Lamp, from 12.06
• After installing a new headlamp power output stage, Headlamp Range/Cornering Lamp Control Module (J745) must be coded --> [ Headlamp Range/Cornering Lamp Control Module, Coding ] Component Tests and General Diagnostics and then basic setting of headlamps must be performed .
5 - Left Cornering Lamp (L148) or Right Cornering Lamp (L149)
• Bulb H7 12V, 55 W
• Replacing --> [ Cornering Lamp Bulb ] HID Headlamps with Cornering Lamp, from 12.06
• Checking --> [ Headlamp Range/Cornering Lamp Control Module Output Diagnostic Test
Mode ] Component Tests and General Diagnostics
6 - Left Front Turn Signal Lamp (M5) and Right Front Turn Signal Lamp (M7)
• Bulb 12V, PY 21 W
• Replacing --> [ Front Turn Signal Bulb ] HID Headlamps with Cornering Lamp, from 12.06
• Checking --> [ Vehicle Electrical System Output Diagnostic Test Mode ] Initial Inspection and Diagnostic Overview
7 - Lamp socket with grip piece
• for Left Front Turn Signal Lamp (M5) and Right Front Turn Signal Lamp (M7)
8 - Cap
9 - Cap
10 - High intensity gas discharge lamp (L13) and High intensity discharge lamp (L14) ("Bi-Xenon")
CAUTION!
Note usage and safety notes for gas discharge headlamps --> [ HID Headlamps Safety Precautions ] HID Headlamps Safety Precautions.
• Type D1S, 35 W
• Replacing --> [ HID Bulb ] HID Headlamps with Cornering Lamp, from 12.06
• Checking --> [ Vehicle Electrical System Output Diagnostic Test Mode ] Initial Inspection and Diagnostic Overview
11 - Left Parking Lamp (M1) and Right Parking Lamp (M3)
• Lamp 12V, W 5 W
• Replacing --> [ Parking Lamp Bulb ] HID Headlamps with Cornering Lamp, from 12.06
• Checking --> [ Vehicle Electrical System Output Diagnostic Test Mode ] Initial Inspection and Diagnostic Overview
12 - Headlamp
• Removing and installing --> [ HID Headlamps ] HID Headlamps with Cornering Lamp, from 12.06
• Correcting installation position of headlamp --> [ Headlamps Correcting Installation Position ] Procedures
• Perform basic setting of headlamps.
13 - Screws
• for mounting headlamp mount on body.
• 5 Nm
14 - Headlamp mount
• Removing and installing --> [ HID Headlamp Mount ] HID Headlamps with Cornering Lamp, from 12.06
15 - Headlamp Range/Cornering Lamp Control Module (J745)
• Component location: at center under instrument panel
• Removing and installing --> [ Headlamp Range/Cornering Lamp Control Module ] HID Headlamps with Cornering Lamp, from 12.06
• Coding --> [ Headlamp Range/Cornering Lamp Control Module, Coding ] Component Tests and General Diagnostics
• Output Diagnostic Test Mode (DTM) --> [ Headlamp Range/Cornering Lamp Control Module Output Diagnostic Test
Mode ] Component Tests and General Diagnostics
• If Headlamp Range/Cornering Lamp Control Module (J745) is coded, headlamp basic setting must then be performed .
- Left Headlamp Reflector Adjustment Solenoid (N395) and Right Headlamp Reflector Adjustment Solenoid (N396)
• Left Headlamp Reflector Adjustment Solenoid (N395) and Right Headlamp Reflector Adjustment Solenoid (N396) are located inside the headlamp and cannot be removed or adjusted.
• Headlamp must be replaced if damaged --> [ HID Headlamps ] HID Headlamps with Cornering Lamp, from 12.06.
• Checking --> [ Vehicle Electrical System Output Diagnostic Test Mode ] Initial Inspection and Diagnostic Overview
- Left Swivel Module Position Sensor (G474) or Right Swivel Module Position Sensor (G475)
• Left Swivel Module Position Sensor (G474) and Right Swivel Module Position Sensor (G475) are located inside the headlamp and cannot be replaced or adjusted separately.
• Headlamp must be replaced if damaged --> [ HID Headlamps ] HID Headlamps with Cornering Lamp, from 12.06.
• Checking --> [ Swivel Module Position Sensor, Checking ] Component Tests and General Diagnostics
- Left Headlamp Beam Adjusting Motor (V48) and Right Headlamp Beam Adjusting Motor (V49)
• Left Headlamp Beam Adjustment Motor (V48) and Right Headlamp Beam Adjustment Motor (V49) is located inside the headlamp and must not be replaced.
• Headlamp must be replaced if damaged --> [ HID Headlamps ] HID Headlamps with Cornering Lamp, from 12.06.
• Checking --> [ Headlamp Range/Cornering Lamp Control Module Output Diagnostic Test
Mode ] Component Tests and General Diagnostics
- Left Dynamic Cornering Lamp Motor (V318) or Right Dynamic Cornering Lamp Motor (V319)
• Left Dynamic Cornering Lamp Motor (V318) and Right Dynamic Cornering Lamp Motor (V319) is located inside the headlamp and must not be replaced.
• Headlamp must be replaced if damaged --> [ HID Headlamps ] HID Headlamps with Cornering Lamp, from 12.06.
• Checking --> [ Headlamp Range/Cornering Lamp Control Module Output Diagnostic Test
Mode ] Component Tests and General Diagnostics