Diagnostic Mode 06 - Read Test Results For Specific Diagnostic Functions
Diagnostic Modes 01 - 09
The information provided in Modes 01 through 09 displays the various levels of emission related data that may be monitored, as well as the ability to retrieve and read stored DTC trouble codes, erase stored DTC trouble codes, generate readiness codes, and select the various PIDs and Test-IDs used within the modes to monitor the engine, and emission related component parameters.
• Depending on scan tool and protocol used, the information in diagnostic mode 01 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).
Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions
Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.
The min & max values for each individual test in Mode 06 represent the min & max operating values for a properly operating system. This data is provided to the individual aftermarket scan tool companies for development of their scan tool. Depending on the scan tool being used, the min & max values shown may vary, or be rounded up or down to the nearest decimal point depending on the aftermarket scan tool company's development process. e.g.:
• Depending on the scan tool and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).
Test requirements
• Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.
• No DTCs stored in the DTC memory.
• Coolant temperature at least 80 °C.
Work procedure
- Connect the scan tool.
- Start the engine and run at idle.
• If the engine does not start, crank the engine using starter for at least 5 seconds, do not switch the ignition off afterward.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
- Select the desired "Monitor-ID" of the component or system that is to be monitored, e.g. "Monitor-ID 01: Oxygen Sensor Monitor Bank 1 - Sensor 1".
- Select the desired "Test-ID".
The current minimum and maximum values will be displayed on the scan tool screen.
The following table is a numerical list of all"Monitor ID's" or "Hex ID's" that may be selected.
Monitor-ID 01: Oxygen Sensor Monitor Bank 1 - Sensor 1
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 01".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID 02: Oxygen Sensor Monitor Bank 1- Sensor 2
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 02".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID 03: Oxygen Sensor Monitor Bank 1- Sensor 3 (CBUA/SULEV only)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 03".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
Monitor-ID 21: Oxygen Storage Content of Catalyst
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 21".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID 35: Variable Valve Timing Monitor
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 3D".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID 3B: Fuel Tank EVAP System Integrity/Leak Test (0.40)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 3B".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID 3C: Fuel Tank EVAP System Integrity/Small Leak Test (0.20)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 3C".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID 3D: EVAP Purge Flow Monitor
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 3D".
- Select the desired "Test-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID 41: Oxygen Sensor Heater Monitor Bank 1 - Sensor 1
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 41".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID 42: Oxygen Sensor Heater Monitor Bank 1 - Sensor 2
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 42".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID 43: Oxygen Sensor Heater Monitor Bank 1 - Sensor 3 (CBUA/SULEV only)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 42".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID 71: Secondary Air Monitor (CBUA/SULEV only)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 71".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID A2:
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A2".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID A3: Mis-Fire Cylinder 2 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6 Check test the results of components that are not continuously monitored".
Select "Monitor-ID A3:".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID A4: Mis-Fire Cylinder 3 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A4".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID A5: Mis-Fire Cylinder 4 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A5".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.
Monitor-ID A6: Mis-Fire Cylinder 5 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A6".
- Select the desired "Test-ID" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure => [ Diagnostic Mode 03 - Read DTC Memory ]. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition OFF.