Comfort System, Power Windows, OBD Remote Control, Programming Ignition Keys
Comfort System, Power Windows, OBD Remote Control, Programming Ignition Keys
NOTE:
- If new or additional ignition keys are required they must be adapted to the immobilizer and Comfort System (vehicles with power windows) control electronics.
- All the keys must be adapted, even the existing ignition keys.
- All the keys must not be adapted again when including a new additional key - Comfort System, Power Windows, OBD Additional Key, Adapting.
- The number of keys already adapted will be displayed when the adaption function is selected.
- With the introduction of this generation of Comfort System (vehicles with power windows) it is possible to program additional functions. The functions and the programming are described from - Comfort System, with Power Windows, Functional Variations
- The adaption procedure can be interrupted by pressing the C button on the VAG1551.
CAUTION: The VAG1551 or the VAS5051 dealership number (workshop code) will be stored in immobilizer control unit when matching ignition keys.
Ignition Keys, Adapting
Requirements
- All ignition keys available. If no old ignition key is available refer to Guided Fault Finding.
- Key fob with covered PIN number is available, if not refer to Guided Fault Finding.
NOTE: Effective calendar date 03.11.2002, the immobilizer secret number is encoded for increased security. The encoded number is now 7-digits and is referred to as a "PIN" ( "Personal Identification Number" ).
- Insert correct profile ignition key in the ignition lock.
- Connecting VAG1551 or VAS5051 - Scan Tool, Connecting and initiating On Board Diagnosis (OBD) - Comfort System OBD, with Power Windows, Initiating.
The adaption shown here is only an example.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press buttons 1 and 0 (10 selects the "Adaptation" function).
Indicated on display:
Rapid data transfer Q
10 - Adaptation
- Confirm entry with Q button.
Indicated on display:
Adaptation
Enter channel number XX
- Press buttons 0 and 0 (all keys are erased with channel number 00).
- Confirm entry with Q button.
NOTE: It is not possible to match a new or additional key(s) without erasing existing learned/matched key(s).
Indicated on display:
Adaptation Q
Erase learnt values?
- Confirm entry with Q button.
Indicated on display:
Adaptation arrowright
Learnt values have been erased
- Press arrowright button.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press buttons 1 and 0 (10 selects the "Adaptation" function).
Indicated on display:
Rapid data transfer Q
10 - Adaptation
- Confirm entry with Q button.
Indicated on display:
Adaptation Q
Enter channel number 01
- Confirm entry with Q button.
Indicated on display:
Channel 1.....Adaptation 1 arrowright
Key 1 -1 3->
The top line displays number of keys to be learned (Standard =1). Select number of keys with buttons 1 and 3.
- Press arrowright button.
Indicated on display:
Channel 1.....Adaptation 1 arrowright
Enter adaption value XXXXX
- Press the 0 button four times and then enter the number of all ignition keys to be adapted, including the existing key, (e.g. 00003); max. Qty of 4 possible.
- Press arrowright button.
Indicated on display: Number of radio wave key to be "learned".
Channel 1 Adaptation 3 Q
Key 3 -1 3->
- Confirm entry with Q button.
Indicated on display:
Channel 1 Adaptation 3 Q
Save amended value?
- Confirm entry with Q button.
Indicated on display:
Channel 1 Adaptation 3 arrowright
Amended value is saved
- Press arrowright button.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Operate button on each of the radio wave remote control keys to be learned/taught once, for at least 1 second (3 keys in above example).
- Switch off ignition and remove ignition key.
- Perform functional check (e.g. 3) of radio wave keys.
NOTE:
- A successful adaptation can be proven in read measured value block (Function 08).
- Comfort System (vehicles with power windows) 2nd generation: Display group number 009 or display group number 013.
- Comfort System (vehicles with power windows) 3rd generation: Display group number 014 or display group number 015.
- All 3 keys (see example) can be learned/taught in one adaptation sequence.
- When adapting all keys (pressing a button), 15 seconds must not be exceeded.
The adaptation of ignition keys is automatically terminated when:
- Number of keys to be adapted is reached.
- A button of one of the keys to be "learned" is pressed frequently.
- Permissible matching period of 15 seconds is exceeded (fault is stored).
- Select function 02 "Check DTC memory". If there is no DTC stored, the matching of the keys has been successfully completed.