Intake Air Temperature Sensor G42, Checking
Intake Air Temperature Sensor G42, Checking
• Use only gold-plated terminals when servicing terminals in the electrical harness connector of the Intake Air Temperature (IAT) Sensor (G42).
Special tools, testers and auxiliary items required
• Multimeter.
• Wiring diagram.
• Cool spray (commercially available).
Test requirements
• The Motronic Engine Control Module (ECM) (J623) fuses OK.
• Battery voltage at least 12.5 volts.
• All electrical consumers such as, lights and rear window defroster, switched off.
• Vehicles with automatic transmission, shift selector lever into position " P" or "N".
• A/C switched off.
• Ground (GND) connections between engine/transmission/chassis OK.
• Ignition switched off.
Test procedure
- Perform a preliminary check to verify the customers complaint. Refer to => [ Preliminary Check ] Preliminary Check.
Start diagnosis
- Connect the scan tool.
- Switch the ignition on.
- Using the scan tool, check the intake air temperature:
If the specified value is not obtained:
- Continue the test according to the following table:
If the specified values are obtained:
- Remove the Intake Air Temperature (IAT) Sensor (G42).
- Spray the Intake Air Temperature (IAT) Sensor (G42) with a commercially available cool spray while observing the temperature value on the scan tool.
The temperature value must decrease.
- End diagnosis and switch the ignition off.
If the intake air temperature does not decrease:
- Replace the Intake Air Temperature (IAT) Sensor (G42).
If the intake air temperature does decrease:
Checking internal resistance
- Disconnect the Intake Air Temperature (IAT) Sensor (G42) electrical harness connector - arrow -.
- Using a multimeter, check the Intake Air Temperature (IAT) Sensor (G42) terminals 1 to 2 for resistance.
Use the chart below for the specified values:
• Area A: Resistance values 0 to 50° C.
• Area B: Resistance values 50 to 100° C.
Specified values:
Read-out examples:
• Range A, 30° C equals a resistance of 1.5 to 2.0 kohms
• Range B, 80° C equals a resistance of 275 to 375ohms
If any of the specified values are not obtained:
- Replace the Intake Air Temperature (IAT) Sensor (G42).
°°Testing if display approx. -40 C or approx. -46 C:
- Disconnect the Intake Air Temperature (IAT) Sensor (G42) electrical harness connector - arrow -.
- Using a jumper wire, connect the Intake Air Temperature (IAT) Sensor (G42) electrical harness connector terminals 1 to 2.
- Check the value indicated on the scan tool display.
If indication jumps to approx. 140° C:
- End diagnosis and switch ignition off.
- Replace the Intake Air Temperature (IAT) Sensor (G42).
If indication remains at approx. -40° C or -46° C:
°Testing if display approx. 140 C:
- Disconnect the Intake Air Temperature (IAT) Sensor (G42) electrical harness connector - arrow -.
If indication jumps to approx. -40° C or -46° C:
- End diagnosis and switch ignition off.
- Replace the Intake Air Temperature (IAT) Sensor (G42).
If the indication remains at approx. 140° C:
Checking wiring
If the manufacturers test box is being used. Perform the following step.
- Install the test box.
If the manufacturers test box is not being used. Perform the following step.
- Remove the Motronic Engine Control Module (ECM) (J623). Refer to => [ Motronic Engine Control Module J623, Replacing ] Motronic Engine Control Module J623, Replacing.
- Using a Multimeter, check the Intake Air Temperature (IAT) Sensor (G42) electrical harness connector terminals to the Motronic Engine Control Module (ECM) (J623) electrical harness connector T60 terminals for an open circuit according to the wiring diagram.
Specified value: 1.5 ohms Max.
If the specification was not obtained:
- Check the wiring for a short circuit to each other, Battery (+), and Ground (GND).
- If necessary, repair the faulty wiring connection.
- Check the electrical harness connector for damage, corrosion, loose or broken terminals.
If no malfunction is detected in the wiring:
- Erase the DTC memory. Refer to => [ Diagnostic Mode 04 - Erase DTC Memory ] Diagnostic Mode 04 - Erase DTC Memory.
- Perform a road test to verify repair.
If the DTC does not return:
Repair complete, Generate readiness code. Refer to => [ Readiness Code ] Readiness Code.
- End diagnosis.
If the DTC does return and no malfunction is detected in the wiring and the voltage supply was not OK:
- Replace the Motronic Engine Control Module (ECM) (J623). Refer to => [ Motronic Engine Control Module J623, Replacing ] Motronic Engine Control Module J623, Replacing.
- Assembly is performed in the reverse of the removal.
Final Procedures
After the repair work, the following work steps must be performed in the following sequence:
1. Check the DTC memory. Refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
2. If necessary, erase the DTC memory. Refer to => [ Diagnostic Mode 04 - Erase DTC Memory ] Diagnostic Mode 04 - Erase DTC Memory.
3. If the DTC memory was erased, generate readiness code. Refer to => [ Readiness Code ] Readiness Code.
End of diagnosis.