Front Passenger Seat Occupant Sensor G128
Airbag
Front Passenger Seat Occupant Sensor G128
CAUTION!
If Front Passenger Seat Occupied Sensor is replaced, also the upholstery, front seat cushion must always be replaced!
Removal
- Mount the (VAS 6136) on the (VAS 6095).
- Remove front seat. Refer to => [ Front Seat ] Front Seats
- Attach the seat to the (VAS 6136).
- Remove the front seat belt latch. Refer to => [ Front Seat Belt Latches ] Service and Repair
- Remove seat cap. Refer to => [ Cover Cap ] Front Seats
Electric seat
- Remove electric seat front end trim. Refer to => [ Power Seat Front Side Trim ] Front Seats
- Remove electric seat trim. Refer to => [ Power Seat Trim ] Front Seats
- Remove electric seat trim bracket. Refer to => [ Power Seat Trim Bracket ] Front Seats
Partially electric seat
- Remove partially electric seat trim. Refer to => [ Partial Power Seat Trim ] Front Seats
- Remove bracket and actuating lever, trim of partially electric/height adjustable seat. Refer to => [ Power Height-Adjustable Seat Trim Bracket and Operating Lever ] Front Seats
Height-adjustable seat
- Remove height-adjustable seat trim. Refer to => [ Height-Adjustable Seat Trim ] Front Seats
- Remove bracket and actuating lever, trim of partially electric/height adjustable seat. Refer to => [ Power Height-Adjustable Seat Trim Bracket and Operating Lever ] Front Seats
Seat without height adjustment
- Remove trim of seat (without height adjuster). Refer to => [ Seat Trim without Height Adjustment ] Front Seats
- Remove bracket, trim, seat (without height adjuster). Refer to => [ Seat Trim Bracket without Height Adjustment ] Front Seats
Passenger Seat with Pass-Through
- Remove the front seat trim. Refer to => [ Passenger Seat Trim with Pass-Through ] Front Seats.
- Remove bracket and actuating lever, trim of partially electric/height adjustable seat. Refer to => [ Power Height-Adjustable Seat Trim Bracket and Operating Lever ] Front Seats
all seats
- Remove front seat backrest. Refer to => [ Left Front Seat Backrest ] Front Seats
- Cover and upholstery, front seat cushion, removing and installing. Refer to => [ Front Seat Cushion ] Front Seat Cover and Upholstery
• Removal of seat occupied sensor is described for Trendline and Comfortline equipment lines. Removal is performed accordingly for Sportline equipment line.
- On seats with a massage-/ventilation function, remove cover - 1 - and loosen seat occupied sensor - 2 - from upholstery - 3 -.
- On seats without massage-/ventilation function, loosen seat occupied sensor - 4 - from upholstery - 5 -.
Installation
Trendline and Comfortline equipment lines
- Position flat wire - 1 - of Front Passenger's Seat Occupied Sensor (G128) into corresponding recess in center of upholstery.
- Pull off adhesive strips - 2 - from Front Passenger's Seat Occupied Sensor (G128) - arrow A - on right side.
- Adhere right sensor strip - 3 - of Front Passenger's Seat Occupied Sensor (G128) on to upholstery.
- Pull off adhesive strips - 4 - from Front Passenger's Seat Occupied Sensor (G128) - arrow B - on left side.
- Adhere left sensor strip - 5 - of the front passenger seat occupant sensor (G128) to the upholstery.
• While adhering, make sure that sensor strips are aligned so that they run parallel to recess in upholstery.
- Position flat wire - 6 - of Front Passenger Seat Occupied Sensor (G128) into corresponding recess on left rear edge of upholstery.
- Pull off adhesive strip - 7 - from Front Passenger Seat Occupied Sensor (G128) - arrow C - and adhere flat wire on to upholstery in this area.
- Position Front Passenger Seat Occupied Sensor (G128) - 8 - and wiring harness - 9 - into corresponding recesses on rear edge of upholstery.
- On seats with a massage-/ventilation function, position cover - 1 - on upholstery, fleece - 2 - must be located on lower side of cover when doing this.
Sportline equipment line
- Position flat wire - 1 - of Front Passenger Seat Occupied Sensor (G128) into corresponding recess of upholstery.
- Slide flat wire forward in direction of travel until the two tabs - 2 - are located in corresponding recess of upholstery.
- Press flat wire - 3 - in rear area of tabs - 2 - into recess of upholstery.
- Pull off adhesive strip - 1 - from Front Passenger Seat Occupied Sensor (G128) - arrow A -.
- Adhere Front Passenger Seat Occupied Sensor (G128) on to upholstery in this area.
- Pull off adhesive strip - 2 - from Front Passenger Seat Occupied Sensor (G128) - arrow B -.
- Adhere Front Passenger Seat Occupied Sensor (G128) on to upholstery in this area.
- Position Front Passenger Seat Occupied Sensor (G128) - 3 - and wiring harness - 4 - into corresponding recesses on rear edge of upholstery.
