Exhaust System Overviews
Exhaust System Overviews
• The decoupling element in the front exhaust pipe must not be bent more than 10°, otherwise it may be damaged.
• Replace gaskets and self-locking nuts.
• After exhaust system repairs, make sure the exhaust system is not under stress and is far enough from the body. If necessary, loosen the clamping sleeve and align the muffler and exhaust pipe so that there is adequate distance to the body and that the weight is evenly distributed among the suspended mounts.
• The exhaust manifold and turbocharger are one component. For information on removing and installing, refer to => [ Turbocharger ] Turbocharger.
Eos and GTI for MY 2008-2009 => [ Engine Code CCTA ]
GTI from MY 2010=> [ Engine Code CCTA ]
=> [ Engine Code CBFA ]
Engine Code CCTA
1 Nut
• 40 Nm
• Always replace
• Lubricate the stud bolts on the exhaust manifold with hot bolt paste (G 052 112 A3).
2 Front Exhaust Pipe with Catalytic Converter
Danger of causing damage to the decoupling element.
• Do not bend the decoupling element more than 10 degrees .
• Do not stretch the decoupling element.
• Do not damage the wire mesh on the decoupling element.
• Protect the catalytic converter from shocks and impact stress.
• Removing and installing, refer to => [ Catalytic Converter with Front Exhaust Pipe ] Exhaust System Components.
• Install the exhaust system free of stress. Refer to => [ Exhaust System, Installing ] Exhaust System Components.
3 Oxygen Sensor (O2S) after Three Way Catalytic Converter (TWC) (G130)
• 55 Nm
• Bank 1, sensor 2
• The threads of new oxygen sensors are coated with hot bolt paste.
• When reusing the previous oxygen sensor, lubricate only the threads with hot bolt paste (G 052 112 A3); the paste must not get into the slots of the oxygen sensor body.
4 Retaining Loop
• Replace if damaged
5 Nut
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components
6 Rear Muffler
• Original equipment as one unit with the center muffler. For repairs, replace each separately.
• Separating the exhaust system. Refer to => [ Center and Rear Muffler, Separating ] Exhaust System Components.
7 Suspended Mount
• Replace if damaged
8 Bolt
• 25 Nm
9 Rear Clamping Sleeve
• For individual replacement of the center and rear mufflers.
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
10 Center Muffler
• Original equipment as one unit with the rear muffler. For repairs, replace each separately.
• Separating the exhaust system. Refer to => [ Center and Rear Muffler, Separating ] Exhaust System Components.
11 Bolt
• 25 Nm
12 Front Clamping Sleeve
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
13 Nut
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
14 Suspended Mount
• For the center muffler.
15 Suspended Mount
• Replace if damaged
16 Gasket
• Always replace
17 Heated Oxygen Sensor (HO2S) (G39)
• 55 Nm
• Bank 1, sensor 1
• The threads of new oxygen sensors are coated with hot bolt paste.
• When reusing the previous oxygen sensor, lubricate only the threads with hot bolt paste (G 052 112 A3); the paste must not get into the slots of the oxygen sensor body.
Engine Code CCTA
1 Nut
• 40 Nm
• Always replace
• Lubricate the stud bolts on the exhaust manifold with hot bolt paste (G 052 112 A3).
2 Front Exhaust Pipe with Catalytic Converter
Danger of causing damage to the decoupling element.
• Do not bend the decoupling element more than 10 degrees .
• Do not stretch the decoupling element.
• Do not damage the wire mesh on the decoupling element.
• Protect the catalytic converter from shocks and impact stress.
• Removing and installing, refer to => [ Catalytic Converter with Front Exhaust Pipe ] Exhaust System Components.
• Install the exhaust system free of stress. Refer to => [ Exhaust System, Installing ] Exhaust System Components.
3 Oxygen Sensor (O2S) after Three Way Catalytic Converter (TWC) (G130)
• 55 Nm
• Bank 1, sensor 2
• The threads of new oxygen sensors are coated with hot bolt paste.
• When reusing the previous oxygen sensor, lubricate only the threads with hot bolt paste (G 052 112 A3); the paste must not get into the slots of the oxygen sensor body.
4 Retaining Loop
• Replace if damaged
5 Nut
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
6 Rear Muffler
• Original equipment as one unit with the center muffler. For repairs, replace each separately.
• Separating the exhaust system. Refer to => [ Center and Rear Muffler, Separating ] Exhaust System Components.
7 Suspended Mount
• Replace if damaged
8 Bolt
• 25 Nm
9 Rear Clamping Sleeve
• For individual replacement of the center and rear mufflers.
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
10 Center Muffler
• Original equipment as one unit with the rear muffler. For repairs, replace each separately.
• Separating the exhaust system. Refer to => [ Center and Rear Muffler, Separating ] Exhaust System Components.
11 Bolt
• 25 Nm
12 Front Clamping Sleeve
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
13 Nut
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
14 Suspended Mount
• For the center muffler.
15 Suspended Mount
• Replace if damaged.
16 Gasket
• Always replace
17 Heated Oxygen Sensor (HO2S) (G39)
• 55 Nm
• Bank 1, sensor 1
• The threads of new oxygen sensors are coated with hot bolt paste.
• When reusing the previous oxygen sensor, lubricate only the threads with hot bolt paste (G 052 112 A3); the paste must not get into the slots of the oxygen sensor body.
Engine Code CBFA
1 Nut
• 40 Nm
• Always replace
• Lubricate the stud bolts on the exhaust manifold with hot bolt paste (G 052 112 A3).
2 Heated Oxygen Sensor (HO2S) 2 (G108)
• 55 Nm
• Bank 1, sensor 2
• The threads of new oxygen sensors are coated with hot bolt paste.
• When reusing the previous oxygen sensor, lubricate only the threads with hot bolt paste (G 052 112 A3); the paste must not get into the slots of the oxygen sensor body.
3 Front Exhaust Pipe with Catalytic Converter
Danger of causing damage to the decoupling element.
• Do not bend the decoupling element more than 10 degrees .
• Do not stretch the decoupling element.
• Do not damage the wire mesh on the decoupling element.
• Protect the catalytic converter from shocks and impact stress.
• Removing and installing, refer to => [ Catalytic Converter with Front Exhaust Pipe ] Exhaust System Components.
• Install the exhaust system free of stress. Refer to => [ Exhaust System, Installing ] Exhaust System Components.
4 Oxygen Sensor (O2S) after Three Way Catalytic Converter (TWC) (G130)
• 55 Nm
• Bank 3, sensor 1
• The threads of new oxygen sensors are coated with hot bolt paste.
• When reusing the previous oxygen sensor, lubricate only the threads with hot bolt paste (G 052 112 A3); the paste must not get into the slots of the oxygen sensor body.
5 Retaining Loop
• Replace if damaged
6 Nut
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
7 Rear Muffler
• Original equipment as one unit with the center muffler. For repairs, replace each separately.
• Separating the exhaust system. Refer to => [ Center and Rear Muffler, Separating ] Exhaust System Components.
8 Suspended Mount
• Replace if damaged.
9 Bolt
• 25 Nm
10 Rear Clamping Sleeve
• For individual replacement of the center and rear mufflers.
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
11 Center Muffler
• Original equipment as one unit with the rear muffler. For repairs, replace each separately.
• Separating the exhaust system. Refer to => [ Center and Rear Muffler, Separating ] Exhaust System Components.
12 Bolt
• 25 Nm
13 Front Clamping Sleeve
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
14 Nut
• Tighten the nuts evenly. Tightening specification and installed position. Refer to => [ Tightening Specification and Installed
Dimension of the Clamping Sleeve ] Exhaust System Components.
15 Suspended Mount
• For the center muffler.
16 Suspended Mount
• Replace if damaged
17 Gasket
• Always replace
18 Heated Oxygen Sensor (G39)
• 55 Nm
• Bank 1, sensor 1
• The threads of new oxygen sensors are coated with hot bolt paste.
• When reusing the previous oxygen sensor, lubricate only the threads with hot bolt paste (G 052 112 A3); the paste must not get into the slots of the oxygen sensor body.