Operation CHARM: Car repair manuals for everyone.

Headlamps, Retrofitting for Left or Right Hand Drive Traffic






Headlamps, Retrofitting for Left or Right Hand Drive Traffic

To prevent dazzling by asymmetrical low beams, both headlamps must be converted to the traffic direction in the corresponding country.

Corresponding headlamp retrofit set consists of two foils each.

The retrofit of the main headlamp is not suitable for long term use in other countries, rather only as short term "tourist solution" during an extended visit to another country.

Both vehicle main headlamps must always be retrofitted.

The labels "right" and "left" on the cover foils always refer to the view forward from the vehicle.

--> [ Headlamps, Right Hand Drive Traffic, Converting to Left ]

--> [ Headlamps, Left Hand Drive Traffic, Converting to Right ]

Headlamps, Right Hand Drive Traffic, Converting to Left

Headlight conversion set consists of two foils.

Pay attention to the different replacement numbers for headlamp retrofit sets for right-hand traffic to left-hand traffic and left-hand traffic to right-hand traffic.

Clean headlamp diffusion lenses before the retrofit.

- Turn light switch into "0" position.

- Clean headlamp diffusion lens.

Left headlamp:

- Remove protective foil on rear side of installation foil - D - only in area - C -.





- Align lower edge of installation foil - D - with line - B - on headlamp lens.

- Align lower edge of installation foil - D - at the same time with radius at line - A - on headlamp lens.

- Press area - C - firmly onto headlamp diffusion lens.

- Carefully pull off installation foil - D - again from diffusion lens.

- Cover oil - C - remains on the headlamp diffusion lens.

Right headlamp:

- Remove protective foil on rear side of installation foil - D - only in area - C -.





- Align lower edge of installation foil - D - with line - B - on headlamp lens.

- Align lower edge of installation foil - D - at the same time with radius at line - A - on headlamp lens.

- Press area - C - firmly onto headlamp diffusion lens.

- Carefully pull off installation foil - D - again from diffusion lens.

- Cover oil - C - remains on the headlamp diffusion lens.

Any remaining residue should be removed with an alcohol- or alcohol-water-based cleaning solution. For example, a cloth moistened with isopropyl alcohol.

Customer should be informed of the instructions to remove adhesive residue after pulling off the cover layer.

Headlamps, Left Hand Drive Traffic, Converting to Right

Headlight conversion set consists of two foils.

Pay attention to the different replacement numbers for headlamp retrofit sets for right-hand traffic to left-hand traffic and left-hand traffic to right-hand traffic.

Clean headlamp lens before converting.

After removing cover foil from lens, remove adhesive residue from headlamp.

- Turn light switch into "0" position.

- Clean headlamp diffusion lens.

Left headlamp:

- Remove protective foil on rear side of installation foil - D - only in area - C -.





- Align lower edge of installation foil - D - with line - B - on headlamp lens.

- Align lower edge of installation foil - D - at the same time with radius at line - A - on headlamp lens.

- Press area - C - firmly onto headlamp diffusion lens.

- Carefully pull off installation foil - D - again from diffusion lens.

- Cover oil - C - remains on the headlamp diffusion lens.

Right headlamp:

- Remove protective foil on rear side of installation foil - D - only in area - C -.





- Align lower edge of installation foil - D - with line - B - on headlamp lens.

- Align lower edge of installation foil - D - at the same time with radius at line - A - on headlamp lens.

- Press area - C - firmly onto headlamp diffusion lens.

- Carefully pull off installation foil - D - again from diffusion lens.

- Cover oil - C - remains on the headlamp diffusion lens.

Any remaining residue should be removed with an alcohol- or alcohol-water-based cleaning solution. For example, a cloth moistened with isopropyl alcohol.

Customer should be informed of the instructions to remove adhesive residue after pulling off the cover layer.