Mode 6 Data

Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions

Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.

Test requirements

• Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.

• No DTCs stored in the DTC memory.

• Coolant temperature at least 80 °C.

Work procedure

- Connect the scan tool.

- Start the engine and run at idle.

• If the engine does not start, crank the engine using starter for at least 5 seconds, do not switch the ignition off afterward under any circumstances.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

- Select the desired "Monitor-ID" of the component or system that is to be monitored, e.g. "Monitor-ID 01: Oxygen Sensor Monitor Bank 1 - Sensor 1".

- Select the desired "Test-ID".

The current minimum and maximum values will be displayed on the scan tool screen.

The following table is a numerical list of all"Monitor-IDs" or " Hex-IDs" that may be selected.





Monitor-ID 01: Oxygen Sensor Monitor Bank 1 - Sensor 1

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 01".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID 02: Oxygen Sensor Monitor Bank 1- Sensor 2

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 02".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID 03: Oxygen Sensor Monitor Bank 1- Sensor 3 (CBUA/SULEV only)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 03".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





Monitor-ID 21: Oxygen Storage Content of Catalyst

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 21".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID 35: Variable Valve Timing Monitor

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 3D".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID 3A: Fuel Tank EVAP System Integrity/Leak Test (0.90")

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 3A".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID 3B: Fuel Tank EVAP System Integrity/Leak Test (0.40)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 3B".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

- Switch the ignition off.

Monitor-ID 3C: Fuel Tank EVAP System Integrity/Small Leak Test (0.20)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 3C".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID 3D: EVAP Purge Flow Monitor

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 3D".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID 41: Oxygen Sensor Heater Monitor Bank 1 - Sensor 1

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 41".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID 42: Oxygen Sensor Heater Monitor Bank 1 - Sensor 2

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 42".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID 43: Oxygen Sensor Heater Monitor Bank 1 - Sensor 3 (CBUA/SULEV only)

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 42".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID 71: Secondary Air Monitor

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID 71".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID A2:

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID A2".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID A3: Mis-Fire Cylinder 2 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6 Check test the results of components that are not continuously monitored".

Select "Monitor-ID A3:".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID A4: Mis-Fire Cylinder 3 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID A4".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID A5: Mis-Fire Cylinder 4 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID A5".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.

Monitor-ID A6: Mis-Fire Cylinder 5 Data

- Connect the scan tool.

- Start the engine and run at idle.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Monitor-ID A6".

- Select the desired "Test-ID" or "Hex-ID".

- Check specified values at idle.





- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure --> [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.

- Switch the ignition off.