B1B11
B1B11 - Driver Knee Bolster Squib Circuit High
For a complete wiring diagram, refer to.
Theory of Operation
When powered, the Occupant Restraint Controller (ORC) sends a test current to the squibs to verify the integrity of the squib and wiring. These circuits are maintained in a "floating" configuration at the module (connected to neither power nor ground) as protection against inadvertent deployment. Use of the SRS Load Tool Kit 8443A in the tests below substitutes a suspect squib with a known good component. The use of the SRS Load Tool Adapter provides a test point as well as a method for opening the shorting bar connections within the harness connector.
• When Monitored: The ORC Module sends out a 40 mA diagnostic current on each squib voltage supply circuit at power up, and every 500 ms thereafter while the ignition is on.
• Set Condition: This Diagnostic Trouble Code (DTC) sets when the ORC detects a short to voltage on the driver knee bolster squib circuit for more than 2.5 seconds. This DTC transitions from active to stored when the ORC sees a recovery from a short to ground for greater than 2.5 seconds.
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding.
Test Step 1 - DETERMINE ACTIVE OR STORED DTC
• Make sure that the battery is fully charged.
• The scan tool, SRS Load Tool Kit 8443A, and DVOM are required to perform the following test.
• Turn the ignition on.
Select ACTIVE or STORED DTC:
ACTIVE DTC
• Go to Test Step 2 => [ Test Step 2 - CHECK FOR SHORTED DRIVER KNEE BOLSTER AIRBAG CIRCUITS ]
STORED DTC
• Perform the Restraints System Intermittent Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Intermittent Test
Test Step 2 - CHECK FOR SHORTED DRIVER KNEE BOLSTER AIRBAG CIRCUITS
Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
• Disconnect the Driver Knee Bolster Airbag harness connector.
Do not place an intact non-deployed airbag face down on a hard surface, the airbag propels into the air if accidentally deployed. Failure to follow these instructions may result in possible serious or fatal injury.
• Check connectors - Clean and repair as necessary.
• Connect the SRS Load Tool Kit 8443A and SRS Load Tool Jumper 8443-8 to the Driver Knee Bolster Airbag harness connector.
Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
• With the scan tool, read the active ORC DTCs.
Does the scan tool display: B1B11-DRIVER KNEE BOLSTER SQUIB CIRCUIT HIGH?
Yes
• Go to Test Step 3 => [ Test Step 3 - CHECK (R11) DRIVER KNEE BLOCKER SQUIB LINE 1 CIRCUIT
OR (R9) DRIVER KNEE BLOCKER SQUIB LINE 2 CIRCUIT FOR A SHORT TO VOLTAGE ]
No
• Replace the Driver Knee Bolster Airbag.
• Perform the Restraints System Verification Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Verification Test
Test Step 3 - CHECK (R11) DRIVER KNEE BLOCKER SQUIB LINE 1 CIRCUIT OR (R9) DRIVER KNEE BLOCKER SQUIB LINE 2 CIRCUIT FOR A SHORT TO VOLTAGE
Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
• Disconnect the SRS Load Tool Kit 8443A from the SRS Load Tool Jumper 8443-8 from the Driver Knee Bolster Airbag harness connector.
• Disconnect the ORC harness connectors.
• Check connectors - Clean and repair as necessary.
• Connect the SRS Load Tool Adapter 8443-28 to the ORC C2 harness connector.
Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
• Measure the voltage of the (R11) Driver Knee Blocker Squib Line 1 circuit between the appropriate terminals of the SRS Load Tool Adapter 8443-28 and ground.
• Measure the voltage of the (R9) Driver Knee Blocker Squib Line 2 circuit between the appropriate terminals of the SRS Load Tool Adapter 8443-28 and ground.
Is there any voltage present on either circuit?
Yes
• Repair the (R11) Driver Knee Blocker Squib Line 1 circuits or (R9) Driver Knee Blocker Squib Line 2 with voltage present for a short to voltage in accordance with the Service Information.
• Perform the Restraints System Verification Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Verification Test
No
• Replace the ORC..
• Perform the Restraints System Verification Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Verification Test
If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to follow these instructions may result in possible serious or fatal injury.
Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.