Operation CHARM: Car repair manuals for everyone.

Lost Communication With Right Side Satellite Acceleration Sensor 3






U0177 - Lost Communication with Right Side Satellite Acceleration Sensor 3







Theory of Operation

The impact sensors perform their own self test using power supplied by the occupant restraint controller then communicate this status back to the ORC with periodic updates. The repair of this fault condition involves verifying the integrity of the wiring between the ORC and the sensor.

When Monitored: The ORC monitors communication with the impact sensor continuously.

Set Condition: This DTC sets when the ORC no longer receives notification of the status update from the impact sensor. Once set, this DTC is latched for the entire ignition cycle.






Always perform the Pre - Diagnostic Troubleshooting procedure before proceeding.

Test Step 1 - Determine Active or Stored DTC

Ensure the battery is fully charged.

Turn the ignition ON.

With the scan tool, read ORC DTCs.

Is the DTC active or stored?

ORC - active DTC

Go to Test Step 2 => [ Test Step 2 - Check for Additional Active Satellite Sensor DTCs ]

ORC - Stored DTC

Perform the Restraints System Intermittent Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Intermittent Test

Test Step 2 - Check for Additional Active Satellite Sensor DTCs

The scan tool, load tool ORC adaptor, and a DVOM are required to perform the following tests.

With the scan tool, read all active ORC DTCs.

Is DTC U0174 - Lost Communication with Left Side Satellite Acceleration Sensor 3 also active?

Yes

Go to Test Step 8 => [ Test Step 8 - Check Right Side Impact Sensor 3 Ground Circuit and
Left Side Impact Sensor 3 Ground Circuit for a Short to Voltage ]

No

Go to Test Step 3 => [ Test Step 3 - Check Right Side Impact Sensor 3 Signal Circuit for
an Open ]

Test Step 3 - Check Right Side Impact Sensor 3 Signal Circuit for an Open







Turn the ignition OFF, disconnect the 12 volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

Disconnect the right side impact sensor 3 connector.

Disconnect the ORC connectors.

Check connectors - Clean and repair as necessary.

Connect the load tool ORC 8443 - 28 adaptor to the ORC connectors.

Measure the resistance of the right side impact sensor 3 signal circuit between the right side impact sensor 3 connector and the load tool ORC 8443 - 28 adaptor.

Is the resistance below 1.0 ohm?

Yes

Go to Test Step 4 => [ Test Step 4 - Check Right Side Impact Sensor 3 Ground Circuit for
an Open ]

No

Repair the right side impact sensor 3 signal circuit for an open. Then, Go to Test Step 4 => [ Test Step 4 - Check Right Side Impact Sensor 3 Ground Circuit for
an Open ]

Test Step 4 - Check Right Side Impact Sensor 3 Ground Circuit for an Open






Measure the resistance of the right side impact sensor 3 ground circuit between the right side impact sensor 3 connector and the load tool ORC 8443 - 28 adaptor.

Is the resistance below 1.0 ohm?

Yes

Go to Test Step 5 => [ Test Step 5 - Check Right Side Impact Sensor 3 Signal Circuit for
a Short to Right Side Impact Sensor 3 Ground Circuit ]

No

Repair the right side impact sensor 3 ground circuit for an open.

Perform the Restraints System Intermittent Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Intermittent Test

Test Step 5 - Check Right Side Impact Sensor 3 Signal Circuit for a Short to Right Side Impact Sensor 3 Ground Circuit






Measure the resistance between the right side impact sensor 3 signal circuit and the right side impact sensor 3 ground circuit at the right side impact sensor 3 connector.

Is the resistance below 5K ohms?

Yes

Repair the right side impact sensor 3 signal circuit for a short to the right side impact sensor 3 ground circuit.

Perform the Restraints System Intermittent Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Intermittent Test

No

Go to Test Step 6 => [ Test Step 6 - Check Right Side Impact Sensor 3 Signal Circuit for
a Short to Ground ]

Test Step 6 - Check Right Side Impact Sensor 3 Signal Circuit for a Short to Ground






Measure the resistance of the right side impact sensor 3 signal circuit between ground and the right side impact sensor 3 connector.

Is the resistance below 5K ohms?

Yes

Repair the right side impact sensor 3 signal circuit for a short to ground.

Perform the Restraints System Intermittent Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Intermittent Test

No

Go to Test Step 7 => [ Test Step 7 - Check Right Side Impact Sensor 3 Signal Circuit for
a Short to Voltage ]

Test Step 7 - Check Right Side Impact Sensor 3 Signal Circuit for a Short to Voltage







Turn the ignition ON, then reconnect the 12 volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

Measure the voltage of the right side impact sensor 3 signal circuit between the right side impact sensor 3 connector and ground.

Is there any voltage present?

Yes

Repair the right side impact sensor 3 signal circuit for a short to voltage.

Perform the Restraints System Intermittent Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Intermittent Test


Turn the ignition OFF, disconnect the 12 volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

No

Perform the Restraints System Intermittent Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Intermittent Test

Test Step 8 - Check Right Side Impact Sensor 3 Ground Circuit and Left Side Impact Sensor 3 Ground Circuit for a Short to Voltage







Turn the ignition OFF, disconnect the 12 volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

Disconnect the left side impact sensor 3 connector.

Disconnect the right side impact sensor 3 connector.

Disconnect the ORC connectors.

Check connectors - Clean and repair as necessary.

Connect the load tool ORC 8443 - 28 adaptor to the ORC connectors.


Turn the ignition ON, then reconnect the 12 volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

Measure the voltage of the left side impact sensor 3 ground circuit between the load tool ORC 8443 - 28 adaptor and ground.

Measure the voltage of the right side impact sensor 3 ground circuit between the load tool ORC 8443 - 28 adaptor and ground.

Is there any voltage present on either circuit?

Yes

Repair the impact sensor circuit with voltage present for a short to voltage.

Perform the Restraints System Intermittent Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Intermittent Test


Turn the ignition OFF, disconnect the 12 volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

No

Go to Test Step 9 => [ Test Step 9 - Check Operation of Right Side Impact Sensor 3 ]

Test Step 9 - Check Operation of Right Side Impact Sensor 3


Turn the ignition OFF, disconnect the 12 volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

Replace the right side impact sensor 3.

Reconnect the vehicle body harness to the impact sensor.

Remove any special tools or jumper wires and reconnect all previously disconnected components - except the battery.


Turn the ignition ON, then reconnect the 12 volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

Connect the scan tool to the DLC - use the most current software available.

With the scan tool, erase all codes in the ORC.

Perform ORC module reset. Access the miscellaneous function menu from the ORC ECU overview screen on the scan tool to perform this operation.

Wait one minute, and read active codes.

Did the Active DTC U0177 - Lost Communication with Right Side Satellite Acceleration Sensor 3 return?

Yes

Replace the ORC.

Perform the Restraints System Intermittent Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Intermittent Test


If the occupant restraint controller is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment. Failure to follow these instructions may result in possible serious or fatal injury.


Turn the ignition OFF, disconnect the 12 volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

No

Repair is complete.

Perform the Restraints System Intermittent Test. Refer to => Non - DTC Based Diagnostics. ORC Restraints System Intermittent Test