Part 2

Output Shaft, 1st to 4th Gears

Continued from, Part 1

Installing the Locking Collar/Synchronizer Hub for 1st and 2nd Gears

Turn the synchronizer ring so that the grooves line up with the locking pieces.

- Install the locking ring.

Install the 1st gear synchronizer ring

Installation Position of the 1st Gear Outer Race

The tabs - arrows - face the synchronizer hub/locking collar - A -.

Installed Position: Synchronizer Ring - A - (1st Gear Inner Race)

The tabs - arrows 1 - engage into the holes - arrows 2 - inside the synchronizer ring - B -.

Install the 1st Gear with Needle Roller Bearing

The higher collar - A - faces the 2nd gear - B -. The notches in the collar - arrow - lock into the tabs on the outer race. Refer to => [ Installation Position of the 1st Gear
Outer Race ].

- Install the thrust washers for 1st and 4th gears => [ (Item 19) Thrust Washer ] Output Shaft, 1st to 4th Gears Overview and => [ (Item 20) Washer ] Output Shaft, 1st to 4th Gears Overview.

- Install the 4th gear with needle bearing.

Checking the 4th Gear Synchronizer Ring for Wear

- Press the synchronizer ring onto the taper of the gear and measure the gap dimension - a - using a feeler gauge.

Installed Position: Locking Collar/Synchronizer Hub for 3rd and 4th Gears

The wider collar on the synchronizer hub - arrow - faces 3rd gear.

Installing the Synchronizer Hub with Locking Collar for 3rd and 4th Gears

- Turn the synchronizer ring so that the grooves line up with the locking pieces.

- Install the locking ring.

- Install the 3rd gear synchronizer ring on the synchronizer hub/locking collar for 3rd and 4th gears.

Installed Position: 3rd Gear Outer Race

The tabs - arrows - face the synchronizer hub/locking collar - A -.

Installed Position: Synchronizer Ring - A - (3rd Gear Inner Race)

The tabs - arrows 1 - engage into the holes - arrows 2 - inside the synchronizer ring - B -.

Installed Position: 3rd Gear

The higher collar - A - faces toward the 4th gear - B -. The notches in the collar - arrow - lock into the tabs on the outer race. Refer to => [ Installation Position of the 1st Gear
Outer Race ].

- Install the 3rd gear with the needle bearing.

• Pressing on the inner race/tapered roller bearing. Refer to => [ Installing the Inner Race/Tapered Roller
Bearing on the Side of the Transmission Housing ].

• Selecting the locking ring for the inner race/tapered roller bearing. Refer to => [ Selecting the Locking Ring ].

Assembling, from Transmission Build Date 26 October 2009 through 24 May 2000

Checking the Inner Contact Surface for Wear on the 1st Gear Outer Race and on the 2nd Gear Outer Race

- Install the inner race - 1 - on the cone on the gear.

- Install the outer race - 2 - on the cone on the inner race. Measure the gap - a - with a feeler gauge at 3 locations at 120°.

- Note the average value.

Checking the Outer Contact Surface for Wear on the 1st Gear Outer Race and on the 2nd Gear Outer Race

- Check the synchronizer ring - arrow - on the inner running surface for grooves and radial wear, and replace if necessary.

- Install the inner race, the outer race and the synchronizer ring on the cone on the inner race.

- Press the synchronizer ring onto the outer races while turning it at the same time so that it seats correctly.

- Measure the gap - a - with a feeler gauge at 3 locations at 120°.

- Note the average value.

- Install the 2nd gear with the needle bearing.

Installed Position of the Outer Race, Inner Race and Synchronizer Ring, 2nd Gear

- Install the inner race - A - in the gear.

The tabs - 1 - face away from the gear.

- Install the outer race - B -.

The tabs - 2 - engage in grooves - 3 - on the gear.

- Install the synchronizer ring - C -.

The larger openings - 4 - lock in the tabs - 1 - on the inner race - A -.

Disassembling and Assembling the Locking Collar and the Synchronizer Hub for 1st, 2nd, 3rd and 4th Gears

1. Spring

2. Locking piece

3. Locking collar

4. Synchronizer hub

- Slide the locking collar over the synchronizer hub.

In 3rd and 4th gear, the wide collar on the synchronizer hub and the locking collar face in one direction.

The notches for the locking pieces on the synchronizer hub and locking collar must line up with each other.

Assembly: Locking Collar/Synchronizer Hub for 1st, 2nd, 3rd and 4th Gears

The locking collar is pushed over the synchronizer hub.

- Install the locking pieces and springs offset by 120°. The angled end of the spring must engage into the hollow locking piece.

Installed Position: Locking Collar/Synchronizer Hub for 1st and 2nd Gears

The identification groove - arrow 1 - and the narrow collar - arrow 2 - on the synchronizer hub face 1st gear.

Installing the Locking Collar/Synchronizer Hub for 1st and 2nd Gears

The pins - A - on the synchronizer ring lock into the recesses - B - in the synchronizer hub.

- Install the locking ring.

Installing the Synchronizer Ring for 1st Gear Outer Race and Inner Race

- Install the synchronizer ring - A - in the synchronizer hub.

The tabs - 1 - lock in the openings - 2 - in the synchronizer hub.

- Install the outer race - B - in the synchronizer ring.

The tabs - 3 - face away from the synchronizer ring.

- Install the inner race - C - in the outer race.

The tabs - 4 - lock in the larger openings - 5 - in the synchronizer ring - A -.

Install the 1st Gear with Needle Roller Bearing

• The synchronizer ring - 1 - and the tabs - arrow A - are inside the openings in the synchronizer hub - 2 -.

The pins - arrows B - in the outer race lock in the recesses - arrows C - in the gear - 3 -.

- Install the thrust washers for 1st and 4th gears => [ (Item 19) Thrust Washer ] Output Shaft, 1st to 4th Gears Overview and => [ (Item 20) Washer ] Output Shaft, 1st to 4th Gears Overview.

- Install the 4th gear with needle bearing.

Checking the 4th Gear Synchronizer Ring for Wear

- Press the synchronizer ring onto the taper of the gear and measure the gap dimension - a - using a feeler gauge.

Installed Position: Locking Collar/Synchronizer Hub for 3rd and 4th Gears

The wider collar on the synchronizer hub - arrow - faces 3rd gear.

- Place the synchronizer ring for 4th gear on the 4th gear selector gear.

Installing the Synchronizer Hub with Locking Collar for 3rd and 4th Gears

- Turn the synchronizer ring so that the grooves line up with the locking pieces.

- Install the locking ring.

Checking the 3rd Gear Inner Race for Wear

- Install the inner race onto the taper of the selector gear and then measure gap dimension - a - with a feeler gauge.

Checking the Synchronizer Ring for 3rd Gear for Wear

- Install the synchronizer ring, outer race and inner race onto the taper of the selector gear and then measure the gap dimension - a - with a feeler gauge.

- Install the 3rd gear synchronizer ring on the synchronizer hub/locking collar for 3rd and 4th gears.

Installed Position: 3rd Gear Outer Race

The tabs - arrows - face the synchronizer hub/locking collar - A -.

Installed Position: Synchronizer Ring - A - (3rd Gear Inner Race)

The tabs - arrows 1 - engage into the holes - arrows 2 - inside the synchronizer ring - B -.

Installed Position: 3rd Gear

The higher collar - A - faces toward 4th gear - B -. The notches in the collar - arrow - lock into the tabs on the outer race. Refer to => [ Installation Position of the 1st Gear
Outer Race ].

- Install the 3rd gear with the needle bearing.

• Pressing on the inner race/tapered roller bearing. Refer to => [ Installing the Inner Race/Tapered Roller
Bearing on the Side of the Transmission Housing ].

• Selecting the locking ring for the inner race/tapered roller bearing. Refer to => [ Selecting the Locking Ring ].

Assembling, from Transmission Build Date 25 May 2000

Checking the Inner Contact Surface for Wear on the 1st Gear Outer Ring, the 2nd Gear Outer Ring, and the 3rd Gear Outer Ring

Checking the Outer Contact Surface for Wear on the 1st Gear Outer Ring, the 2nd Gear Outer Ring, and the 3rd Gear Outer Ring

- Install the 2nd gear with the needle bearing.

Installed Position of the Outer Race, Inner Race and Synchronizer Ring, 2nd Gear

The identification groove - arrow 1 - and the narrow collar - arrow 2 - on the synchronizer hub face 1st gear.

Installing the Locking Collar/Synchronizer Hub for 1st and 2nd Gears

The pins - A - on the synchronizer ring lock into the recesses - B - in the synchronizer hub.

- Install the locking ring.

Installing the Synchronizer Ring for 1st Gear Outer Race and Inner Race

- Press the synchronizer ring onto the taper of the gear and measure the gap dimension - a - using a feeler gauge.

Installed Position: Locking Collar/Synchronizer Hub for 3rd and 4th Gears

- Turn the synchronizer ring so that the grooves line up with the locking pieces.

- Install the locking ring.

Installing the Outer Ring Synchronizer Ring and 3rd Gear Inner Ring

• The synchronizer ring - 1 - and the tabs - arrow A - are inside the openings in the synchronizer hub - 2 -.

The pins - arrows B - in the outer race lock in the recesses - arrows C - in the gear - 3 -.

- Install the 3rd gear with the needle bearing.

• Pressing on the inner race/tapered roller bearing. Refer to => [ Installing the Inner Race/Tapered Roller
Bearing on the Side of the Transmission Housing ].

• Selecting the locking ring for the inner race/tapered roller bearing. Refer to => [ Selecting the Locking Ring ].