Power Liftgate Control Module

Power Liftgate Control Module

Special tools, testers and auxiliary items required

• Trim removal wedge (RMCP101)

Removing

- Open the liftgate.

- Disconnect and isolate the battery negative cable.

- Remove the liftgate scuff plate.

- Using (RMCP101) disengage the liftgate scuff plate clips (1).






- Carefully disengage the scuff plate end tabs (4) from the left and right quarter trim panels (5).

- Remove the liftgate scuff plate (3) from the liftgate opening.

- Remove the upper D-pillar trim.

- Using trim removal wedge (RMCP101) disengage the upper D-pillar trim clips (2).






- Carefully disengage the upper D-pillar trim end tab (5) from the rear header trim plate.

- Disconnect the power liftgate D-pillar switch and third row power folding seat switch electrical connectors (3) (if equipped).

- Remove the upper D-pillar trim from the liftgate opening.

- Remove the quarter trim bolster (5).






- Using trim removal wedge (RMCP101) disengage the front and rear quarter trim bolster clips (1).

- Carefully disengage the quarter trim bolster upper tabs (2) by lifting the bottom edge of the bolster.

- Continue pulling the quarter trim bolster away from the quarter trim panel to disengage the quarter trim bolster locating tabs (4).

- Slide the rear seat belt (3) out of the slot in the quarter trim bolster.

- Remove the quarter trim bolster (5).

- Remove the left quarter trim panel (5).






- Remove the third row lower seat belt webbing anchor (4).

- Remove the third row upper turning loop anchor bolt.

- Remove the six quarter trim screws.

- Pull trim from inner quarter panel (1).

- Disconnect the auxiliary power outlet and power inverter (2) wire harness connectors (3) (if equipped).

- Remove the left quarter trim panel (5).

- If equipped, remove the subwoofer.

- Disconnect the wire harness connectors (4) from the power liftgate control module (2).






- Remove the power liftgate control module retainer (3).

- Tilt the rear of the module (2) away from the quarter panel and disengage the mounting tab from the locating slot (1).

- Remove the power liftgate control module (2) from the vehicle.

Installing

- Position the power liftgate control module (2) into the vehicle.






- Insert the mounting tab into the locating slot on the inner quarter panel (1).

- Install the power liftgate control module push pin style retainer (3).

- Connect the wire harness connectors (4) to the power liftgate control module.

- If equipped, install the subwoofer.

- Install the left quarter trim panel (5).






- Position the left quarter trim panel (5) into the vehicle.

- Connect the auxiliary power outlet and power inverter (2) wire harness connectors (3) (if equipped).

- Align the trim panel over the retaining slots on the inner quarter panel (1) and firmly snap into place.

- Install the six quarter trim screws.

- Install the third row upper turning loop anchor bolt.

- Install the third row lower seat belt webbing anchor (4).

- Install the quarter trim bolster (5).






- Position the quarter trim bolster (5) into the vehicle and slide the rear seat belt (3) into the slot.

- Align the locating tabs (4) with the holes in the left quarter trim panel.

- Carefully engage the quarter trim bolster upper tabs (2) by inserting them into the left quarter trim panel and swinging the bottom edge of the bolster towards the left quarter trim.

- Push the quarter trim bolster into the left quarter trim panel until the clips (1) are fully seated.

- Install the upper D-pillar trim.

- Position the upper D-pillar trim into the liftgate opening.

- Connect the power liftgate D-pillar switch and third row power folding seat switch electrical connectors (3) (if equipped).






- Carefully engage the upper D-pillar trim end tab (5) into the rear header trim plate.

- Push the upper D-pillar trim onto the D-pillar to engage the trim clips (2).

- Install the liftgate scuff plate.

- Position the liftgate scuff plate (3) into the liftgate opening.






- Carefully engage the scuff plate end tabs (4) into the left and right quarter trim panels (5).

- Push the liftgate scuff plate down onto the liftgate opening to engage the scuff plate clips (1).

- Connect the battery negative cable.

- Using an appropriate scan tool, check and erase any power liftgate control module diagnostic trouble codes.

- Perform the power liftgate learn cycle. Refer to => [ Power Liftgate Learn Cycle ] Power Liftgate Learn Cycle.

- Verify power liftgate system operation.