Heated Seat Module
Heated Seat Module
Description
The heated seat module (2) is located under the driver front seat. It has a single electrical connector (1) and a push pin style retainer that secures it to the seat pan. The module can be accessed from under the front driver seat with the seat in the full rearward position.
The heated seat module is a microprocessor designed to use the local interface network data bus messages from the instrument cluster also known as the cabin compartment node. The CCN receives inputs from the heated seat switches and rear door modules and in turn signals the heated seat module to operate the heated seat elements for the appropriate seats.
Operation
Front Seat Heated Seat System
The front heated seat system operates on battery current received through a fuse in the totally integrated power module. Fused ignition switch output circuits are used, so that the systems will only operate when the ignition switch is in the on position. The heated seat system will turn off automatically whenever the ignition switch is turned to any position except on. If the ignition switch is turned to the off position while a heated seat is on, the heated seat will remain off after the engine is restarted until a front seat heated seat switch is depressed again. This prevents the vehicles battery from being drained by the heated seat system.
The heated seat switches for the front row seats are located in rear heating, ventilation and air conditioning control unit. The rear HVAC control is mounted in the lower portion of the instrument panel center stack. Amber light emitting diodes in the top portion of each switch indicate the level of heat in use: Two LED's are illuminated for high, one for low, and none for off. Pressing the switch once will select the highest level of heating. Pressing the switch a second time will select the lowest level of heating. Pressing the switch a third time will shut the heating elements off.
A heated seat module is used to control the heated seat system. The module is secured to a mounting bracket located under the driver front seat. The module responds to heated seat switch messages and ignition switch status inputs by controlling the 12 volt output to the seat heating elements through integral solid-state relays.
When either of the front heated seat switches are depressed a resistance signal is sent to the electromechanical instrument cluster. The instrument cluster receives this message via the controller area network data bus. The instrument cluster then sends a message via the LIN data bus to the heated seat module, signaling the module to energize the heating element for the selected seat.
The heated seat module energizes an integral solid state relay, which supplies battery current to the heating elements. Heated seats turn off after one hour of continuous operation. If the highest level of heating is selected, the control system will remain at the high level for 30 minutes and then drop to the low level for 30 minutes. Then it will turn off. At that time, the number of illuminated LED's changes from two to one, indicating the change.
The module will automatically turn off the heating elements if it detects an open or low short in the heating element circuit.
Second Row Heated Seat System
The 2nd row heated seat system operates on battery current received through a fuse in the TIPM. Fused ignition switch output circuits are used, so that the systems will only operate when the ignition switch is in the on position. The heated seat system will turn off automatically whenever the ignition switch is turned to any position except on. If the ignition switch is turned to the off position while a heated seat is on, the heated seat will remain off after the engine is restarted until a 2nd row seat heated seat switch is depressed again. This prevents the vehicles battery from being drained by the heated seat system.
The heated seat switches for the 2nd row seats are located in the sliding door trim panels near the door handles. Amber LED's in the top portion of each switch indicate the level of heat in use: Two LED's are illuminated for high, one for low, and none for off. Pressing the switch once will select the highest level of heating. Pressing the switch a second time will select the lowest level of heating. Pressing the switch a third time will shut the heating elements off.
The 2nd row heated seat system utilizes the same heated seat module as the front heated seat system. The module is secured to a mounting bracket located under the Driver front seat. The module responds to heated seat switch messages and ignition switch status inputs by controlling the 12 volt output to the seat heating elements through integral solid-state relays.
When either of the 2nd row heated seat switches are depressed a hard wired resistance signal is sent to the applicable rear door module (left or right). The applicable rear door module then sends a message via the CAN data bus network to the EMIC. The instrument cluster then sends a message via the LIN data bus to the heated seat module, signaling the module to energize the heating element for the selected seat. LED's in each switch indicate the level of heat in use. The switch LED's are controlled by the applicable rear door module.
The heated seat module energizes an integral solid state relay, which supplies battery current to the heating elements. Heated seats turn off after one hour of continuous operation. If the highest level of heating is selected, the control system will remain at the high level for 30 minutes and then drop to the low level for 30 minutes. Then it will turn off. At that time, the number of illuminated LED's changes from two to one, indicating the change.
The module will automatically turn off the heating elements if it detects an open or low short in the heating element circuit.