HID Headlamps with Cornering Lamp Overview, Through 11.06
HID Headlamps with Cornering Lamp Overview, Through 11.06
• Check for possible influences upon the headlamp adjustment, check the adjustment itself, and if needed, adjust the headlamps. Refer to Maintenance Procedures; Rep. Gr. 03.
- Tightening Specifications, refer to=> [ Fastener Tightening Specifications, Headlamp ] [1][2]Headlamp.
1 - Adjusting Shaft For Low Beam And High Beam Height Adjustment
2 - Connector
• to Left High-intensity Gas Discharge Lamp Control Module (J343) or Right High-intensity Gas Discharge Lamp Control Module (J344) .
3 - Screws
• For mounting left/right HID lamp control modules to bracket.
4 - Left High-intensity Gas Discharge Lamp Control Module (J343) and Right High-intensity Gas Discharge Lamp Control Module (J344)
• Left High-intensity Gas Discharge Lamp Control Module (J343) and Right High-intensity Gas Discharge Lamp Control Module (J344) is not capable of On Board Diagnostic (OBD).
• Removing and installing, refer to => [ HID Headlamp Control Module ] HID Headlamp Control Module.
5 - Screws
• For mounting bracket to headlamp housing.
6 - Bracket
7 - Cable Ties
• For securing wire to bracket.
8 - Left Cornering Lamp (L148) or Right Cornering Lamp (L149)
• Bulb H7 12V, 55 W
• Removing and installing, refer to => [ Cornering Lamp Bulb ] Cornering Lamp Bulb.
• Checking, refer to => [ Cornering Lamp and Headlamp Range Control Module, Output Diagnostic Test Mode ] Cornering Lamp and Headlamp Range Control Module (J745), Output Diagnostic Test Mode.
9 - Cap
10 - Headlamp Range/Cornering Lamp Control Module (J745)
• Component location: at center under instrument panel.
• Removing and installing, refer to => [ Cornering Lamp and Headlamp Range Control Module ] Cornering Lamp and Headlamp Range Control Module (J745).
• Coding, refer to => [ Cornering Lamp and Headlamp Range Control Module, Coding ] Cornering Lamp and Headlamp Range Control Module (J745), Coding.
• Output Diagnostic Test Mode (DTM), refer to => [ Cornering Lamp and Headlamp Range Control Module, Output Diagnostic Test Mode ] Cornering Lamp and Headlamp Range Control Module (J745), Output Diagnostic Test Mode.
• Adapting, refer to => [ Cornering Lamp and Headlamp Range Control Module, Adapting ] Cornering Lamp and Headlamp Range Control Module (J745), Adapting.
• Perform a basic setting on the headlamp if the Headlamp range/cornering lamp control module (J745) was coded. Refer to Maintenance Procedures; Rep. Gr. 03.
11 - High Intensity Gas Discharge Lamp (L13) and High Intensity Discharge Lamp (L14) ("Bi-Xenon")
Note usage and safety notes for gas discharge headlamps Refer to => [ HID Headlamps, Usage and Safety Precautions ] Service Precautions.
• Type D1S, 35 W
• Removing and installing, refer to => [ HID Bulb ] HID Bulb.
• Checking, refer to => [ Vehicle Electrical System, Output Diagnostic Test Mode ] Scan Tool Testing and Procedures.
12 - Wiring
• Between Left High Intensity Gas Discharge (HID) Lamp (L13) or Right High Intensity Gas Discharge (HID) Lamp (L14) and Left High-intensity Gas Discharge Lamp Control Module (J343) or Right High-intensity Gas Discharge Lamp Control Module (J344).
13 - Left Parking Lamp (M1) and Right Parking Lamp (M3)
• Lamp 12V, W 5 W
• Removing and installing, refer to=> [ Parking Lamp Bulb ] Parking Lamp Bulb.
• Checking, refer to=> [ Vehicle Electrical System, Output Diagnostic Test Mode ] Scan Tool Testing and Procedures.
14 - Headlamp
• Removing and installing, refer to=> [ Headlamps ] Headlamps.
• Correcting installation position of headlamp, refer to=> [ Headlamps, Correcting Installation Position ] Headlamps, Correcting Installation Position.
• Perform a basic setting on the headlamp. Refer to Maintenance Procedures; Rep. Gr. 03.
15 - Left Headlamp Power Output Stage (J667) or Right Headlamp Power Output Stage (J668)
• Removing and installing, refer to=> [ Headlamp Power Output Stages ] Headlamp Power Output Stages.
• After installing a new headlamp power output stage, Headlamp range/cornering lamp control module (J745) must be coded, refer to=> [ Cornering Lamp and Headlamp Range Control Module, Coding ] Cornering Lamp and Headlamp Range Control Module (J745), Coding and then basic setting of headlamps must be performed. Refer to Maintenance Procedures; Rep. Gr. 03.
16 - Screws
• For mounting left/right headlamp power output stage to headlamp.
17 - Adjustment Bushings
18 - Screws
• For front headlamp mount.
19 - Headlamp Mount
• Left Headlamp Mount, 6-Cylinder TDI, removing and installing, refer to=> [ HID Left Headlamp ] HID Left Headlamp.
• Left Headlamp Mount, 6-Cylinder Gasoline, removing and installing, refer to=> [ HID Left Headlamp Mount ] HID Left Headlamp Mount.
• Left Headlamp Mount, 10-Cylinder TDI and 8-Cylinder Gasoline, removing and installing, refer to=> [ HID Left Headlamp Mount ] HID Left Headlamp Mount.
• Right Headlamp Mount, 6-Cylinder TDI, removing and installing, refer to=> [ HID Right Headlamp Mount ] HID Right Headlamp Mount.
• Right Headlamp Mount, 6-Cylinder Gasoline, removing and installing, refer to=> [ HID Right Headlamp Mount ] HID Right Headlamp Mount.
• Right Headlamp Mount, 10-Cylinder TDI and 8-Cylinder Gasoline, removing and installing, refer to=> [ HID Right Headlamp Mount ] HID Right Headlamp Mount.
20 - Securing Clip
21 - Locking Bolt
22 - Alignment Bushings
• For mounting bolts of rear headlamp mount.
23 - Screws
• For rear headlamp mount.
24 - Connector
25 - Securing Clip
26 - Left Front Turn Signal Light (M5) and Right Front Turn Signal Light (M7)
• Bulb 12V, PY 21 W
• Removing and installing, refer to=> [ Front Turn Signal Bulb ] Front Turn Signal Bulb.
• Checking, refer to=> [ Vehicle Electrical System, Output Diagnostic Test Mode ] Scan Tool Testing and Procedures.
27 - Cap
28 - Lamp Socket With Grip Piece And Harness Connector
• For Left front turn signal bulb (M5) and Right front turn signal bulb (M7)
29 - Screws
• For mounting the adjusting shaft for low beam and high beam height adjustment.
- Left Headlamp Reflector Adjustment Solenoid (N395) and Right Headlamp Reflector Adjustment Solenoid (N396)
• Left Headlamp Reflector Adjustment Solenoid (N395) and Right Headlamp Reflector Adjustment Solenoid (N396) are located inside the headlamp and cannot be removed or adjusted.
• If a failure occurs, the entire headlamp must be replaced. Refer to => [ Headlamps ] Headlamps.
• Checking, refer to => [ Vehicle Electrical System, Output Diagnostic Test Mode ] Scan Tool Testing and Procedures.
- Left Swivel Module Position Sensor (G474) or Right Swivel Module Position Sensor (G475)
• Left Swivel Module Position Sensor (G474) and Right Swivel Module Position Sensor (G475) are located inside the headlamp and cannot be replaced or adjusted separately.
• If a failure occurs, the entire headlamp must be replaced. Refer to => [ Headlamps ] Headlamps.
- Left Headlamp Beam Adjustment Motor (V48) and Right Headlamp Beam Adjustment Motor (V49)
• Left Headlamp Beam Adjustment Motor (V48) and Right Headlamp Beam Adjustment Motor (V49) is located inside the headlamp and must not be replaced.
• If a failure occurs, the entire headlamp must be replaced. Refer to => [ Headlamps ] Headlamps.
• Checking, refer to => [ Cornering Lamp and Headlamp Range Control Module, Output Diagnostic Test Mode ] Cornering Lamp and Headlamp Range Control Module (J745), Output Diagnostic Test Mode.
- Left Dynamic Cornering Light Motor (V318) or Right Dynamic Cornering Light Motor (V319)
• Left Dynamic Cornering Light Motor (V318) and Right Dynamic Cornering Light Motor (V319) is located inside the headlamp and must not be replaced.
• If a failure occurs, the entire headlamp must be replaced. Refer to => [ Headlamps ] Headlamps.
• Checking, refer to => [ Cornering Lamp and Headlamp Range Control Module, Output Diagnostic Test Mode ] Cornering Lamp and Headlamp Range Control Module (J745), Output Diagnostic Test Mode.