Output Shaft, 5th, 6th and Reverse Gears Overview

Output Shaft, 5th, 6th and Reverse Gears Overview

• Heat the bearing inner race/tapered roller bearing and synchronizer hub to approximately 100 °C (212 °F) using the inductive heat unit (VAS 6414). Wear protective gloves.

• Replace both tapered roller bearings together.

• Adjust the output shaft if it or the tapered roller bearing are being replaced. Refer to => [ Output Shaft, 5th, 6th and Reverse Gears, Adjusting ] Output Shaft, 5th, 6th and Reverse Gears, Adjusting.






1 Clutch Housing

2 Washer

• Always 0.65 mm thick.

3 Outer Race/Tapered Roller Bearing

• Removing, refer to => [ Removing the Outer Race/Tapered Roller Bearing ] Output Shaft, 5th, 6th and Reverse Gears.

• Installing, refer to => [ Installing the Outer Race/Tapered Roller Bearing in the Clutch Housing ] Output Shaft, 5th, 6th and Reverse Gears.

4 Bearing Inner Race/Taper Roller Bearing

• Removing, refer to => [ Removing the Bearing Inner Race/Tapered Roller Bearing on the Side of the Clutch Housing ] Output Shaft, 5th, 6th and Reverse Gears.

• Installing, refer to => [ Installing the Bearing Inner Race/Tapered Roller Bearing on the Side of the Clutch Housing ] Output Shaft, 5th, 6th and Reverse Gears.

5 Output Shaft

• For 5th, 6th and reverse gears.

• Adjusting, refer to => [ Output Shaft, 5th, 6th and Reverse Gears, Adjusting ] Output Shaft, 5th, 6th and Reverse Gears, Adjusting.

6 Reverse Gear Synchronizer Hub

• Removing, refer to => [ Removing the Reverse Gear Synchronizer Hub ] Output Shaft, 5th, 6th and Reverse Gears.

• Installed position, refer to => [ Installed Position: Reverse Gear Synchronizer Hub ] Output Shaft, 5th, 6th and Reverse Gears.

• Installing, refer to => [ Heating and Installing the Reverse Gear Synchronizer Hub ] Output Shaft, 5th, 6th and Reverse Gears.

7 Locking Ring

8 Reverse Gear Locking Collar

• With the synchronizer ring.

9 Needle Bearing

• For reverse gear.

10 Reverse Gear

11 Sleeve

• Remove with the reverse gear, refer to => [ Removing the Sleeve together with the Reverse Gear ] Output Shaft, 5th, 6th and Reverse Gears.

• Installed position: The wider sleeve collar faces the reverse gear.

• Installing, refer to => [ Installing the Sleeve ] Output Shaft, 5th, 6th and Reverse Gears.

12 Locking Ring

13 Needle Bearing

• For 6th gear.

14 6th Gear

15 6th Gear Synchronizer Ring

• Checking for wear, refer to => [ Checking the 5th and 6th Gear Synchronizer Ring for Wear ] Output Shaft, 5th, 6th and Reverse Gears.

16 Locking Collar with Synchronizer Hub for 5th and 6th Gears

• After removing the locking ring - item 17 -, remove the 6th gear. Refer to => [ Removing the 5th and 6th Gear Synchronizer Hub/Locking Collar and the 6th Gear ] Output Shaft, 5th, 6th and Reverse Gears.

• Disassembling, refer to => [ Disassembling and Assembling the Locking Collar and Synchronizer Hub for 5th and 6th Gears ] Output Shaft, 5th, 6th and Reverse Gears.

• Assembling the locking collar/synchronizer hub, refer to => [ Disassembling and Assembling the Locking Collar and Synchronizer Hub for 5th and 6th Gears ] Output Shaft, 5th, 6th and Reverse Gears and to => [ Assembling the Locking Collar/Synchronizer Hub for 5th and 6th Gears ] Output Shaft, 5th, 6th and Reverse Gears.

• Installing, refer to => [ Installing the Locking Collar/Synchronizer Hub for 5th and 6th Gears ] Output Shaft, 5th, 6th and Reverse Gears.

17 Locking Ring

18 Needle Bearing

• For 5th gear.

19 5th Gear Synchronizer Ring

• Checking for wear, refer to => [ Checking the 5th and 6th Gear Synchronizer Ring for Wear ] Output Shaft, 5th, 6th and Reverse Gears.

20 5th Gear

21 Bearing Inner Race/Taper Roller Bearing

• Removing, refer to => [ Remove the Bearing Inner Race/Tapered Roller Bearing on the Side of the Transmission Housing ] Output Shaft, 5th, 6th and Reverse Gears.

• Installing, refer to => [ Installing the Bearing Inner Race/Tapered Roller Bearing on the Side of the Transmission Housing ] Output Shaft, 5th, 6th and Reverse Gears.

22 Locking Ring

• Select the correct one when replacing the tapered roller bearing - item 21 - and the output shaft - item 5 -. Refer to => [ Selecting the Locking Ring ] Output Shaft, 5th, 6th and Reverse Gears.

23 Outer Race/Tapered Roller Bearing

• Removing, refer to => [ Removing the Outer Race/Tapered Roller Bearing from the Transmission Housing ] Output Shaft, 5th, 6th and Reverse Gears.

• Installing, refer to => [ Installing the Outer Race/Tapered Roller Bearing into the Transmission Housing ] Output Shaft, 5th, 6th and Reverse Gears.

24 Adjusting Shim

• To select the correct thickness, refer to => [ Output Shaft, 5th, 6th and Reverse Gears, Adjusting ] Output Shaft, 5th, 6th and Reverse Gears, Adjusting.

25 Transmission housing

26 Spring

• Installed position, refer to => [ Assembling the Locking Collar/Synchronizer Hub for 5th and 6th Gears ] Output Shaft, 5th, 6th and Reverse Gears.

27 Locking Collar

28 Synchronizer Hub

29 Locking Pieces

• Quantity: 3

• Installed position, refer to => [ Disassembling and Assembling the Locking Collar and Synchronizer Hub for 5th and 6th Gears ] Output Shaft, 5th, 6th and Reverse Gears.