Subframe Transverse Link And Tie Rods FWD From MY 2011
Overview: Subframe Transverse Link And Tie Rods FWD From MY 2011
1 Eccentric Screw
• For camber setting
• Perform a vehicle alignment after loosening. Refer to => [ Vehicle Alignment Procedure ] Vehicle Alignment Procedure
2 Eccentric Screw
• For toe setting
• Perform a vehicle alignment after loosening. Refer to => [ Vehicle Alignment Procedure ] Vehicle Alignment Procedure
3 Eccentric Washer
• Inner bore with tab
4 Nut
• 95 Nm
• M12 x 1.5
• Self-locking.
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Axle in Curb Weight Position ] Rear Suspension.
5 Eccentric Washer
• Inner bore with tab
6 Nut
• 95 Nm
• M12 x 1.5
• Self-locking
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Axle in Curb Weight Position ] Rear Suspension.
7 Subframe
8 Bolt
• 90 Nm + 90°
• M12 x 1.5 x 95
• Always replace if removed.
9 Lower Transverse Link
• Removing and installing, refer to => [ Lower Transverse Link FWD From MY 2011 ] Lower Transverse Link FWD From MY 2011
10 Nut
• 90 Nm + 90°
• M12 x 1.5
• Self-locking
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Axle in Curb Weight Position ] Rear Suspension.
11 Bolt
• Always replace if removed.
12 Threaded Rivet
• M6
13 Expanding Rivet
14 Stone Chip Protection
• Allocation, refer to the Parts Catalog
15 Bolt
• 8 Nm
16 Nut
• 130 Nm + 90°
• M14 x 1.5
• Self-locking
• Always replace if removed.
17 Washer
18 Bolt
• 130 Nm + 90°
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Axle in Curb Weight Position ] Rear Suspension.
19 Washer
20 Upper Transverse Link
• Removing and installing, refer to => [ Upper Transverse Link FWD From MY 2011 ] Upper Transverse Link FWD From MY 2011
21 Washer
22 Nut
• M14 x 1.5
• Self-locking
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Axle in Curb Weight Position ] Rear Suspension.
23 Wheel Bearing Housing
• Removing and installing, refer to => [ Wheel Bearing Housing, FWD ] Wheel Bearing Housing, FWD
24 Washer
25 Bolt
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Axle in Curb Weight Position ] Rear Suspension.
26 Tie Rod
• closed in direction of travel (the right and left tie rods are different)
• Allocation, refer to the Parts Catalog
• Removing and installing, refer to => [ Tie Rod, FWD ] Tie Rod, FWD
27 Bolt
• Always replace if removed.
28 Nut
• 90 Nm + 90°
• M12 x 1.5
• Self-locking
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Axle in Curb Weight Position ] Rear Suspension.