HID Headlamp with Dynamic High Beam Control Overview
HID Headlamp with Dynamic High Beam Control Overview
• Check for possible influences upon the headlamp adjustment, check the adjustment itself, and if needed, adjust the headlamps. Refer to => Work Descriptions.
1 - Left Side Marker Lamp Bulb (M1) and Right Side Marker Lamp Bulb (M3)
• Replacing, refer to => [ Left Side Marker Lamp Bulb (M1)/Right Side Marker Lamp Bulb (M3) ] Left Side Marker Lamp Bulb (M1)/Right Side Marker Lamp Bulb (M3).
2 - Left Front Turn Signal Bulb (M5) and Right Front Turn Signal Bulb (M7)
• Bulb 12V, PSY24W SV
• Replacing, refer to => [ Left Front Turn Signal Bulb (M5)/Right Front Turn Signal Bulb (M7) ] Left Front Turn Signal Bulb (M5)/Right Front Turn Signal Bulb (M7).
3 - Lamp Socket with Grip
• For left front turn signal bulb and right front turn signal bulb.
4 - Cap
5 - Screws
• For attaching the left or right HID lamp control module to the cap - Item 4 -.
6 - Left High-intensity Gas Discharge Lamp Control Module (J343) and Right High-intensity Gas Discharge Lamp Control Module (J344)
• Left High-intensity Gas Discharge Lamp Control Module (J343) and Right High-intensity Gas Discharge Lamp Control Module (J344) is not capable of On Board Diagnostic (OBD).
• Removing and Installing, refer to => [ Left HID Headlamp Control Module (J343)/Right HID Headlamp Control Module (J344) ] Left HID Headlamp Control Module (J343)/Right HID Headlamp Control Module (J344).
7 - Screws
• For attaching the headlamp power output stage to the cap.
8 - Left Headlamp Power Output Stage (J667) or Right Headlamp Power Output Stage (J668)
• Removing and Installing, refer to => [ Left Headlamp Power Output Stage (J667)/Right Headlamp Power Output Stage (J668) ] Left Headlamp Power Output Stage (J667)/Right Headlamp Power Output Stage (J668).
• Code the cornering lamp and headlamp range control module (J745) and perform a basic setting on the headlamp after installing a new headlamp power output stage. Refer to => Procedure Description.
9 - Cap
10 - Left HID Headlamp Bulb (L13) and Right HID Headlamp Bulb (L14) ("Bi-Xenon")
Note usage and safety notes for gas discharge headlamps => [ HID Headlamps, Usage and Safety Precautions ] Service Precautions.
• Type D3S, 35W.
• Replacing, refer to => [ Left HID Headlamp Bulb (L13)/Right HID Headlamp Bulb (L14) ] Left HID Headlamp Bulb (L13)/Right HID Headlamp Bulb (L14).
11 - Left Headlamp Beam Adjustment Motor (V48) and Right Headlamp Beam Adjustment Motor (V49)
• Removing and Installing, refer to => [ Left Headlamp Beam Adjustment Motor (V48)/Right Headlamp Beam Adjustment Motor (V49) ] Left Headlamp Beam Adjustment Motor (V48)/Right Headlamp Beam Adjustment Motor (V49).
12 - Headlamps
• Removing and Installing, refer to => [ Headlamp ] Headlamp.
• Correcting installation position of headlamp, refer to => [ Adjusting Headlamp, Installed Position ] Adjusting Headlamp, Installed Position.
• Headlamp, Changing from LHD to RHD, refer to => [ Headlamps, Retrofitting for Left or Right Hand Drive Traffic ] Headlamps, Retrofitting for Left or Right Hand Drive Traffic.
• Headlamp Mounting Tabs, Servicing, refer to => [ Headlamp Mounting Tabs, Servicing ] Headlamp Mounting Tabs, Servicing.
• Perform a basic setting on the headlamp. Refer to => Procedure Description.
13 - Adjustment Bushing
• Correcting installation position of headlamp, refer to => [ Adjusting Headlamp, Installed Position ] Adjusting Headlamp, Installed Position.
14 - Screws
• For attaching the headlamp
• Tightening specifications: 5 Nm
15 - Cornering Lamp And Headlamp Range Control Module (J745)
• Component location: On a cross bar behind the radio/navigation system.
• Removing and Installing, refer to=> [ Cornering Lamp and Headlamp Range Control Module (J745) ] Cornering Lamp and Headlamp Range Control Module (J745).
• Coding; refer to => [ Cornering Lamp and Headlamp Range Control Module (J745), Coding ] Cornering Lamp and Headlamp Range Control Module (J745), Coding.
• Output Diagnostic Test Mode (DTM); refer to => [ Headlamp Range/Cornering Lamp Control Module (J745), Output Diagnostic Test Mode ] Headlamp Range/Cornering Lamp Control Module (J745), Output Diagnostic Test Mode.
• Mounting bolt tightening specification: 2 Nm.
• Perform a basic setting on the headlamp if the headlamp range/cornering lamp control module (J745) was coded. Refer to => Procedure Description.