Removal and Replacement
Cylinder head/gasket, replacing
Special tools:
999 5452 CAMSHAFT ADJUSTMENT TOOL 999 5452 Camshaft Adjustment Tool
999 5454 PRESS TOOL 999 5454 Press Tool
999 5670 Pliers 999 5670 Pliers
999 5451 ADJUSTMENT TOOL 999 5451 Adjustment Tool
951 2050 BEVEL PROTRACTOR 951 2050 Bevel Protractor
951 2767 Roller 951 2767 Roller
999 5450 PUNCH 999 5450 Punch
999 5718 Drift 999 5718 Drift
999 5719 Drift 999 5719 Drift
Note! Since the illustrations in the information are used for different model years and/or models, there may be some deviations. However, the essential information in the illustrations is always correct.
Removing the cylinder head gasket
Preparation
Remove
- the radiator breather tube from the expansion tank. Install lock grip pliers
- the negative battery lead. First read Battery, disconnecting Battery Disconnecting.
- the right front wheel.
Draining coolant
Raise the car.
Remove the splash guard under the engine.
Open the engine nipple.
Drain the coolant into a container.
Close the nipple.
Removing components
Remove
- the clamp between the oil pressure pipe and the oil return line at the turbocharger (TC)
- the pipe screw that holds the oil pressure pipe to its connector on the cylinder block
- the oil return line. Seal the opening in the cylinder block
- the screws and spacers at the exhaust manifold support bracket
- the lower screw that holds the heat deflector plate over the turbocharger (TC)
- the nuts for the front exhaust pipe connection to the turbocharger (TC).
Lift off the exhaust pipe and tie it up. Seal the opening in the exhaust pipe.
Note! The front exhaust pipe's metal hose is very sensitive to twisting. Handle it with care to avoid leakage later on.
Draining the fuel line
Lower the car.
Drain the fuel line. See Fuel system pressure release Fuel System Pressure Release.
Removing components
Remove
- the engine stabilizer brace between the suspension turrets.
- the ground strips between the engine and the bulkhead
- the heat deflector plate above the turbocharger (TC).
- the plastic charge air pipe above the engine. Seal the openings
- the cover over the ignition coils
- the upper engine coolant hose for the engine and radiator
- the screw holding the dip stick pipe to the intake manifold.
- the brake vacuum hose from the intake manifold.
Undo the clamp holding the plastic charge air pipe to the electronic throttle module.
Remove
- the connector from the mass air flow (MAF) sensor.
- the intake hose from the mass air flow (MAF) sensor. Seal the opening.
Release the hoses from the bracket at the rear of the cylinder head. Remove the bracket.
Remove
- the clamp for the positive lead at the rear of the cylinder head
- the torque bracket.
- the pipe screw for the water-heated crankcase ventilation.
Removing the fuel rail
Remove the clamp for the injector wiring at the rear of the cylinder head.
Separate the fuel line quick-release connector.
Remove the fuel rail mounting screws.
Spray universal oil or similar around the injector connectors on the intake manifold.
Gently work the fuel rail and injectors loose.
Carefully put the fuel rail to one side.
Removing ignition coils
Mark up the ignition coils so that the original positions can be established.
Remove the mounting screws for the ignition coils and the screws at the two ground terminals.
Disconnect the connector for the variable valve timing solenoid.
Lift up and place the ignition coils and wiring to one side.
Remove
- the crankcase ventilation hose from the top of the camshaft cover
- the camshaft position sensor (CMP) housing and trigger wheel
- the cover at the rear edge of the intake camshaft.
Removing the intake manifold
Remove
- the EVAP hose from the intake manifold
- the by-pass valve vacuum hose
- the upper row of screws holding the intake manifold to the cylinder head. Slacken off the lower screws
- the pipe screw for the crankcase ventilation from the underside of the intake manifold.
Disconnect the connector for the electronic throttle module.
Lift up and remove the intake manifold.
Note! Make sure that the fuel delivery pipe is not damaged.
Removing components
Disconnect the connectors for the ABS sensor and level sensor in the expansion tank.
Lift up the expansion tank and servo oil reservoir. Place them on top of the engine.
Note! Make sure that power steering fluid does not leak from the breather hole in the filler cap.
Take off the auxiliaries belt.
Remove
- the front timing cover
- the hose for the water-heated crankcase ventilation from the thermostat housing.
Separate the connector for the engine coolant temperature (ECT) sensor.
Setting up the engine
Remove the nuts from the cover on the wing liner.
Position the upper timing cover.
Turn the crankshaft clockwise until the markings on the crankshaft and camshafts correspond.
Remove the upper timing cover.
Removing the timing belt
Slacken off the centre screw for the belt tensioner slightly.
Hold the center screw secure and turn the tensioner eccentric clockwise with a 6 mm Allen key to 10 o'clock.
Remove
- the timing belt from the timing gear pulley
- the screw that holds the inner timing cover to the cylinder head.
Install tool 999 5452 CAMSHAFT ADJUSTMENT TOOL 999 5452 Camshaft Adjustment Tool at the rear of the camshafts.
Removing the timing gear pulley
Remove the cable duct from its mountings on the right-hand suspension turret.
Note! Do not damage the paint work.
Hold the cable duct out of the way and remove
- the plug at the front of the variable valve timing unit (TX55)
- the centre screw in the variable valve timing unit (TX55).
Carefully pull out the timing gear pulley with the variable valve timing (VVT) unit.
Timing gear pulleys without variable valve timing units:
Remove the screws and remove the timing belt pulley.
Remove tool 999 5452 CAMSHAFT ADJUSTMENT TOOL 999 5452 Camshaft Adjustment Tool.
Removing components from turbocharger (TC)
Remove
- the upper coolant pipe with the hose
- the heat deflector plate above the manifold
- the oil pressure pipe for the turbocharger (TC)
- the pipe screw at the lower coolant pipe for the turbocharger (TC). Put the pipe to one side.
- the nuts and washers holding the manifold to the cylinder head.
Lift off the turbocharger and manifold. Carefully put them on top of the gearbox.
Releasing the inlet pipe for the coolant pump
Remove
- the screw that holds the inlet pipe for the coolant pump on the cylinder block
- the two screws for the connection between the coolant pipe and the bypass channel.
Carefully turn the pipe to remove it from the cylinder block.
Removing the camshaft cover and cylinder head
Remove the spark plugs from cylinders 1 and 5.
Install 2 tools 999 5454 PRESS TOOL 999 5454 Press Tool. Leave a 2-3 mm gap to the camshaft cover.
Make sure that the screw in the spark plug thread is tightened all the way down. VVT-solenoid.
Remove all the screws securing the camshaft cover to the cylinder head.
Use pliers 999 5670 Pliers 999 5670 Pliers to lift the cover from the cylinder head.
Install the pliers at the stop lugs. Start with cylinder 1 and work alternately backward.
Slacken off the wing nuts approximately 2 turns. Repeat the procedure.
Carefully press out the front and rear camshaft seals.
Remove
- tools 999 5454 PRESS TOOL 999 5454 Press Tool.
- the camshaft cover
- the camshafts
- the screws holding the cylinder head onto the cylinder block.
Start at the sides and work alternately towards the centre.
Get help to lift off the cylinder head.
Note! Work very carefully to avoid damaging the contact faces.
When replacing or working on the cylinder head
Lift out the tappets. Use a magnet or suction cup.
Note! Keep the tappets in an oil-filled container to avoid self-drainage.
Remove the thermostat housing.
Note! Work very carefully to avoid damaging the contact faces.
Cleaning
Cleaning
Clean the gasket faces for
- the manifold. Check that the studs are tightened.
- the coolant bypass channel
- the thermostat housing.
- the intake manifold
- the cylinder block
- camshaft cover.
Blow the oil ducts clean.
Note! Use a razor blade or a gasket scraper and gasket solvent P/N 1161 440.
Warning! When using gasket solvent, work shall be done in a fume hood or by an air extractor!
Cylinder head gasket, installing
Tightening torque
For tightening torques not in the text, see Tightening torque, B5234T9 Tightening Torque.
Setting up the engine
Position the crankshaft
Remove the starter motor mounting screws. Pull out the starter motor and place it to one side.
Remove the blind cover plug
Turn the crankshaft slightly clockwise .
Install crankshaft stop 999 5451 ADJUSTMENT TOOL 999 5451 Adjustment Tool. Ensure that it bottoms out against the cylinder block.
Turn the crankshaft counter-clockwise until it stops against the crankshaft stop
Check that the marking on the crankshaft timing gear pulley corresponds with the marking on the oil pump.
Installing the cylinder head
Ensure that all studs at the exhaust ports are tightened.
Lubricate the studs with paste 116 1408.
Install a new cylinder head gasket.
Install the cylinder head
Lubricate and install all the screws. Use new screws.
Tighten the screws in the order illustrated
Tighten the screws in the following order:
1. 20 Nm
2. 60 Nm .
3. Angle tighten 130° . Use protractor 951 2050 BEVEL PROTRACTOR 951 2050 Bevel Protractor.
Installing tappets and camshafts
Lubricate the valve guide wells.
Install all the tappets.
Lubricate the camshaft bearing seats.
Install the intake camshaft. Ensure that the groove at the back of the camshaft is above an imaginary centre line.
Position the exhaust camshaft. Ensure that the groove at the back of the camshaft is below an imaginary center line
Applying liquid gasket
Install new O-rings around the spark plug wells at the cylinder head.
Apply liquid gasket 1161 059 to the camshaft cover.
Use roller 951 2767 Roller 951 2767 Roller. The surface must be covered without any excess .
Note! Make sure that no liquid gasket gets into the oil channels.
Installing the camshaft cover
Lubricate the camshaft lobes, the camshaft bearing surfaces and the tappets.
Install the camshaft cover.
Install press tool 999 5454 PRESS TOOL 999 5454 Press Tool (2x).
Tighten the camshaft cover screws alternately, keeping it parallel to the cylinder head using the press tools.
Install the intake manifold and lifting eyes, tighten screws from the middle and outwards.
Remove the press tools.
Install:
- the variable valve timing (VVT) solenoid. Use a new gasket
- the spark plugs. Tighten to 30 Nm .
- the hose for water-heated crankcase ventilation to the thermostat housing. Tighten the clamp.
Connect the connector for the engine coolant temperature (ECT) sensor.
Install the inlet pipe for the coolant pump on the cylinder head. Use a new gasket.
Note! Apply thread sealant, 116 056 to the screw threads.
Install the screw for securing the coolant pump intake pipe to the cylinder block.
Installing the manifold and turbocharger (TC)
Install:
- new gaskets.
Lift and install the manifold and turbo.
- the nuts and washers holding the manifold to the cylinder head
- the heat deflector plate above the manifold
- the upper turbocharger (TC) coolant pipes. Tighten the clamp on the rubber hose.
- the pipe screws for the coolant pipes. Use new seal washers. Tighten to 26 Nm .
- the oil pressure pipe
- the pipe screw holding the oil pressure pipe to the turbocharger (TC). Use new seal washers. Do not tighten!
Lubricate the studs on the turbocharger (TC). Use paste 116 1408 .
Install the front exhaust pipe onto the turbocharger (TC). Use new nuts. Do not tighten!
Installing the rear camshaft seal
Use drift 999 5450 PUNCH 999 5450 Punch.
Lubricate the surface of the seal that the camshaft rotates against.
Press in the seal until the drift bottoms out.
Note! If there are grooves on the camshaft, the seal can be pressed in a further 2 mm: Reverse the sleeve.
Install camshaft adjustment tool 999 5452 CAMSHAFT ADJUSTMENT TOOL 999 5452 Camshaft Adjustment Tool at the rear of the camshafts.
Ensure that the screws retaining the adjustment tool to the camshafts and the screws holding the tool together are well tightened.
Installing the front camshaft seals
Use drift 999 5718 Drift 999 5718 Drift for camshaft with variable valve timing unit and drift 999 5719 Drift 999 5719 Drift for camshaft without variable valve timing unit.
Lubricate the surface of the seal that the camshaft rotates against.
Use the variable valve timing unit / timing belt pulley mounting screws. Tighten the screws until the drift bottoms out.
Remove the drift.
Install the screw holding the inner timing cover to the cylinder head.
Variable valve timing unit, checking and adjusting
Check and adjust the variable valve timing unit. See
Installing components
Install:
- front timing cover
- the cable duct to the mountings on the right suspension turret
- the auxiliaries belt
- the expansion tank
- the servo oil reservoir
- the bleed hose to the expansion tank. Tighten the clamp.
Check that the hoses are positioned correctly.
Connect the connectors for the ABS sensor at the right suspension turret and for the coolant level sensor in the expansion tank.
Install
- the starter motor
- the pipe screw for the water-heated crankcase ventilation at the rear of the cylinder head. Use new seal washers. Tighten to 26 Nm .
- the camshaft position sensor (CMP) housing and trigger wheel
- a new cover at the rear of the intake camshaft
- the upper engine stabilizer brace.
Install
- bracket and lifting eyelet for the engine stabilizer brace bracket
- the ignition coils and ground terminals according to earlier markings.
Connect the connector for the variable valve timing solenoid.
- the clamp for the positive lead at the lifting eyelet bracket
- the plastic intake pipe to the mass air flow (MAF) sensor. Tighten the clamp.
Connect the connector to the mass airflow (MAF). Clamp the wiring at the front of the air cleaner (ACL).
Installing the intake manifold
Clean the intake manifold gasket face to the cylinder head.
Install a new gasket on the cylinder head. Secure with the three screws in the lower row.
Lower and twist the intake manifold so that the fuel pressure line goes through the cavity in the intake manifold.
Note! Be very careful so that the fuel delivery pipe is not damaged.
Route the crankcase ventilation hose through the cavity in the intake manifold.
Install
- the pipe screw for the crankcase ventilation on the underside of the intake manifold. Use new seal washers. Tighten to 26 Nm .
- the rest of the screws holding the intake manifold to the cylinder head. Tighten to 19 Nm .
- the hose to the evaporative emission system (EVAP) valve.
- the control hose for the turbocharger (TC) by-pass valve
- the brake vacuum hose.
- the crankcase ventilation hose to the top of the camshaft cover. Use a new clamp
- the cover over the ignition coils
- the upper timing cover
- the upper engine coolant hose for the engine and radiator. Tighten the clamp
- the screw holding the dip stick pipe to the intake manifold.
Connect the connector for the electronic throttle module (ETM).
- the charge air pipe between the throttle body (TB) and the charge air cooler (CAC). Remove the seal. Tighten the clamp.
Installing the fuel rail
Install
- the fuel rail. Use new screws.
Press the quick-release connector for the fuel pressure line until it clicks.
- the clamp for the injector wiring at the rear of the cylinder head
- the protective cover over the injector connectors
- the charge air pipe over the engine. Tighten the pipe using the three screws on the engine. Tighten the clamps.
Installing components
Raise the car. Install
- the pipe screw that holds the turbocharger (TC) oil pressure pipe to the engine. Use new seal washers. Tighten to 38 Nm .
- the turbocharger (TC) oil return line. Use a new gasket and sealing ring. Tighten to 12 Nm .
- the clamp between the oil pressure pipe and the oil return line.
- the screws and spacers at the manifold support bracket and cylinder block.
Tighten the three nuts that hold the front exhaust pipe to the turbocharger (TC). Tighten to 30 Nm .
- the splash guard under the engine.
- the plastic nuts for the hatch in the right fender liner
- the right front wheel. See Installing wheels Removal and Replacement.
Lower the car
Tighten the pipe screw for the turbocharger (TC) oil pressure pipe. Tighten to 26 Nm .
Install
- the heat deflector plate above the turbocharger (TC).
- the ground strips between the cylinder head and the firewall.
- the engine stabilizer brace between the suspension turrets.
Clamp the servo hose at the right engine stabilizer brace mounting.
- the negative battery lead. First read Battery, disconnecting Battery Disconnecting.
Check
Replace the oil and oil filter if necessary.
Check
- the engine oil level
- the servo oil level
- the coolant level.
Warm up the engine until the thermostat opens.
Check the engine for leaks.
Top up the coolant if necessary.