Part 2

Handsfree (Continued)

Cable routing and connection to the accessory electronic module





Applies to the V70
- Fold the rear backrests forward.





Applies to the V70
- Fold the rear seat cushions forward.





Applies to the S60
- Remove the left seat cushion (1) from the rear seat. First pull the front edge of the seat cushion up. Pull the cushion forwards. Then lift the seat cushion out.





Applies to the S60
- Fold forward the left-hand rear backrest
- Remove the seat belt from the guide (1).





Applies to the S60
- Remove the clip (1) at the side of the left-hand side cushion
- Pull out the top edge of the left front panel in the cargo compartment to access the upper catch for the side cushion.





Applies to the S60
- Remove the left-hand side cushion. First press in the catches (1) at the top of the reverse of the side cushion. Pull the cushion out slightly
- Grasp the cushion using both hands. Twist anti-clockwise until the catches on the inside release
- Remove the side cushion. First pull out the top of the side cushion. Then pull upwards.





Applies to the V70
- Remove both side cushions. First pull the upper edge of the cushions backwards. Then lift the cushions upwards.





Applies to the S60/V70
- Remove the sill trim panel at the left rear door.





Applies to the V70
- Remove both the floor hatches. First lift the rear edges of the floor hatches slightly. Then pull the hatches backwards from their mountings.





Applies to the V70
- Remove the foldable panels on the left and right-hand sides of the cargo compartment.





Applies to the V70
- Remove the left-hand side panel. First remove the cover and the screw at the front edge of the panel
- Pull the top of the panel out until the clips release
- Fold the panel inwards. Lift the panel out
- Repeat the operation on the right-hand side.





Applies to the V70
- Remove the storage box from under the rear floor hatch by turning the clip on the left and right-hand sides 90°. Lift out the box.





Applies to the S60
- Remove the cargo compartment carpet at the rear edge. First turn the two knobs (1) 90°.





Applies to the S60
- Pull up the front of the cargo compartment carpet. Fold the front half back over the rear half of the cargo compartment carpet.





Applies to the S60
- Slide the entire cargo compartment carpet forward slightly. Twist slightly to remove the carpet through the tailgate opening
- Remove the cargo compartment carpet.





Applies to the S60
- Press the centres of the clips at the bottom of the folding side panel on the left-hand side. Press the clips until a click is heard
- Remove the two clips
- Remove the plastic nut at the front edge of the side panel
- Repeat the operation on the right-hand side.





Applies to the S60
- Turn the handle (1) on the right and left-hand sides. Turn through 90°.
- Fold the side panels down. Lift the panels out
- Pull the tailgate sill trim panel (2) forwards on the right and left-hand sides until the clips on each side release. Carefully pull the panel. Pull with some force as it is tightly secured
- Remove the wiring (3) for the cargo compartment lighting
- Pull the sill trim panel straight up until the four clips on the underneath release. Remove the sill trim panel.





Applies to the S60
- Remove the clips (1) from the left front side panel in the cargo compartment. Remove the panel.





Applies to the S60/V70
- Applies only to the V70: Take the foam tape from the kit. Install the section of the long single cable to be routed under the sill trim panel for the tailgate. This is to prevent rattling
- Take the long single cable that was routed with the cable harness from the radio. Route the cable under the carpet to the left-hand side of the car
- Clamp the cable at the existing cable harness at the left-hand side of the cross member. Use a tie strap (1) from the kit
- Route the cable inside the carpet and under the cable ducts (2) and (3) along the left-hand side of the car towards the cargo compartment. Ensure that the cable is securely pressed down between the sills and carpets
- Route the cable under the existing wiring and the connectors by the cable duct (3).





Applies to the V70 Illustration 50A
- Route the cable along the left rear wheel arch to the rear end of the left floor support
- Remove the outer screws (1) in the tailgate sill trim panel
- Pull up the tailgate sill trim panel on the left-hand side. Insert the cable between the floor support and the sill trim panel
- Slide the cable in towards the rear crossmember as far as possible. Ensure that the cable is not trapped
- Route the cable along the existing cable harness at the rear crossmember over to the right-hand side. Insert the cable between the sill trim panel and the floor support in the same way as on the left-hand side.





Illustration 50B
- Clamp the cable using tie straps (2)
- Press the sill trim panel back into place. Reinstall the two screws.





Applies to the S60
- Route the cable along the left-hand rear wheel well to the rear crossmember
- Continue to route the cable along the rear crossmember over the rear edge of the right-hand rear wheel well
- Clamp the cable along the existing cable harnesses using tie straps (1).





Applies to the S60/V70
- Slacken off the screw (1) a few turns in the lock facing for the accessory electronic module behind the right wheel well
- Pull the lock facing out to the right. Remove the lock facing.





Applies to the S60/V70
- Lift the accessory electronic module out of the bracket.





Applies to the S60/V70
- Disconnect the large connector from the accessory electronic module. First press in catch (A). Pull the black lock handle (B) in the direction of the arrow until a click is heard
- Disconnect the connector from the accessory electronic module.





Applies to the S60/V70
- Remove the black catch holding the black switch in place in the connector by pulling in the direction of the arrow
- Remove the black switch. Insert a pointed object in the hole on the other end of the connector. Press the switch out.





Applies to the S60/V70
- Connect the pre routed cable to the Accessory Electronic Module connector in terminal 11.

Note! The number markings can be found on the top and bottom of the black switch. However, the markings are extremely small so be careful when installing the cable.





Applies to the S60/V70
- Reinstall the black switch in the connector. Lock into place using the catch
- Press the connector into the accessory electronic module. Secure the connector using the black lock handle
- Reinstall the accessory electronic module. Secure any excess wiring
- Reinstall the lock facing above the accessory electronic module. Tighten the screw. Tighten to 10 Nm (8 lbf. ft.)
- Program the software according to the service information in VIDA.

Installing the handsfree box

Applies to both Ericsson and Nokia





Hint: Install the aerial according to the separate Installation Instructions.

- Tip the driver's seat back slightly
- Position the hands free box and the bracket with the mounting over the screw hole in the right front mounting for the driver's seat
- Fold the seat down towards the mountings. Check that the bracket for the hands free box is positioned under the seat rail
- Clamp the cables. The seat must be able to move without the wiring stretching or breaking.

Note! Ensure that the none of the wiring is trapped.

- Tighten the front edge of the seat using two new screws from the kit. Tighten to 40 Nm (30lbfft).

Finishing work





Reinstall:
- the soundproofing panel
- the side panel on the centre console
- the radio
- the dashboard environmental panel
- the panel around the gear selector lever
- the covers for the front seat screws
- the bracket for the loudspeaker grille
- the loudspeaker grille.

Applies to cars with a storage compartment
- Install the storage compartment. Tighten using the four screws
- Reinstall the surround for the storage compartment.

Applies to cars with a centrally mounted loudspeaker
- Connect the connector to the loudspeaker
- Reinstall the loudspeaker and bracket. Tighten the loudspeaker and bracket using the four screws
- Reinstall the loudspeaker grille.

Applies to cars with RTI (road traffic information)
- Connect the connector to the RTI display (and to the centrally mounted loudspeaker if applicable)
- Reinstall the RTI unit and holder and, where applicable, the centrally mounted loudspeaker. Tighten the four screws
- Reinstall the panel.

Applies to the V70
- Reinstall the storage box in the cargo compartment
- Reinstall the floor hatches in the cargo compartment
- Fold the backrest and left-hand seat cushion back into position.

Applies to the S60
- Reinstall the cargo compartment carpet
- Reinstall the rear seat cushion.

Applies to the S60/V70
- Reinstall the panels in the cargo compartment
- Reinstall the side cushion
- Reinstall the sill trim panels on the left-hand side
- Turn the ignition key to position II
- Reconnect the battery negative lead.

Applies to the Ericsson T28 and T20 after installing the carphone holder
- Place the carphone in the holder. Check that the cover on the carphone does not catch when it is opened.

Illustration 60A applies to the T28





If the cover catches:
- Remove the outer section (1) of the carphone holder
- Slacken off the screw (2) slightly so that the intermediate section (3) of the carphone holder can be turned in its mounting (4)
- Place the carphone with the cover open in the carphone holder
- Test the carphone holder in different positions. When the optimum position is found, remove the carphone. Screw the carphone holder into place on the mounting.

Illustration 60 B applies to the T20





If the cover catches:
- Remove the carphone holder (4) from the intermediate section (1)
- Slacken off the screw (3) slightly so that the intermediate section (1) of the carphone holder can be turned in its mounting (2)
- Place the carphone with the cover open in the carphone holder
- Test the carphone holder in different positions. When the optimum position is found, remove the carphone. Screw the carphone holder into place on the mounting.