Accessory Electronic Module With Wiring Kit

Accessory Electronic Module With Wiring Kit







- Turn the ignition key to position 0
- Cars with manual gearboxes: Remove the ignition key
- Disconnect the battery negative lead.

NOTE: Wait at least five minutes before disassembling the connectors or removing other electrical equipment.







- Remove the seat cushion (1). First pull the front edge of the seat cushion up. Pull the cushion forwards. Then lift the seat cushion out.







- Fold both the rear backrests forward
- Remove the seat belts from the guides (1).







- Insert your hand down the side of the lower section of the side cushion. Remove the left-hand side cushion
- Release the catches. At the same time lift the side cushion
- Place the cushion to one side
- Repeat the operation on the other side.







- Remove the cargo compartment carpet (1)
- Turn the clip (2) for the left and right side panels. Remove the clips and the plastic nut. Remove the panels
- Remove the two covers (3). Slacken off the two screws (4) from under the cover. Grip the outer edges of the panel (5). Pull the panel inwards towards the centre so that the clips release at the sides. Disconnect the connectors (6) for the cargo compartment lamps
- Remove the panel by pulling it straight upwards so that the clips release from the rear crossmember.







Remove:

- the clips (1) from the left front side panel in the cargo compartment
- the panel. Place the panel to one side
- repeat the operation on the other side.
- Push the insulation panel to one side under the seat cushion on both sides







- Route the new cable harness along the side of the cargo compartment and out into the passenger compartment.
- Position the end of the cable with the two large grey connectors on the left-hand side of the car under the seat cushion by the cable duct
- Route the cable harness from the left-hand cable duct under the seat cushion, along the wheel arch and out through the hole in the car body behind the backrest. Then route along the wheel arch and rear crossmember over to the right-hand side of the car
- Continue to route the cable harness along the right-hand side of the cable duct and forward into the car. Then route the cable out through the hole in the car body behind the lower edge of the backrest. Continue to the existing ground terminals under the seat cushion
- Secure the cable harness at the existing cable harnesses and cable duct. Use the tie straps (1) (from the kit)
- Find the pre-routed grey connector (2) by the left-hand tail lamp. Connect the grey connector to the corresponding connector (3) from the routed cable harness.







- Remove the connector (1) from the terminal (2) above the cable duct under the rear seat cushion
- Connect the connector (3) from the routed cable harness to the terminal (2)
- Connect the connector (4) from the routed cable harness to the disconnected connector (1). Wrap foam tape (from the kit) around them
- Hide the connectors under the insulation panel
- Fold the insulation panel back into place.







- Install the new bracket on the right-hand rear side member.
- Install and tighten the bracket parallel with the side member. Use the screw and the nut from the kit
- Tighten to 10 Nm (8 lbf.ft.)
- Drill a 4 mm (5/32 inches) hole in the side member, through the front hole in the bracket
- Tighten the front mounting for the bracket to the side member. Use a self tapping screw from the kit
- Remove any swarf. Rust-proof the hole edge.







Applies to cars equipped with a Diversity antenna amplifier
- Wrap foam tape around the cable/wiring for the antenna amplifier.

Applies to all models
- Take the accessory electronic module from the kit. Connect the cable and connector previously routed along the right-hand side member.







- Press the control module onto the bracket by the side member.







- Slacken off the rear screw (1) in the bracket for the accessory electronic module a few turns
- Insert the grooved end of the lock facing (2) under the screw head. Position.
- Tighten the screw. Tighten to 10 Nm (8 lbf. ft.).







- Install the fuse from the kit in position 11 in the fuse holder.
- Reinstall the panels in the cargo compartment
- Reinstall the two screws in the tailgate sill trim panel
- Reinstall the side cushion
- Fold the backrest back into place
- Reinstall the seat cushions.







- Turn the ignition key to position II
- Reconnect the battery negative lead
- Reinstall the cargo compartment carpet
- Reinstall both floor hatches
- Program the software.