Programming the Control Module, Central Electronic Module (CEM)
Programming the control module
Programming procedures
The following can be programmed into the central electronic module (CEM) to meet statutory requirements and fulfill customer wishes.
Programming:
1. Seat temperature
2. Home safe lights
3. Daytime running lamps
4. Tailgate wiper (5 door models)
5. Time delay, locking the fuel tank filler cover
6. Warning for low beam position (Bi-Xenon).
Use the buttons to select the functions to be programmed.
1 - Programming the seat temperature
2 - Programming the home safe lights
3 - Programming the daytime running lamps
4 - Programming the wiper function for the rear windshield (5 door models)
5 - fuel tank filler cover lock
6 - Programming the warning for low beam position (Bi-Xenon)
-------------------------------------------------
Programming the seat temperature
Programming the seat temperature (central electronic module)
Programming the seat temperature (central electronic module)
The heated seat temperature can be adjusted.
This can be carried out for both the left and right seats.
There are two values that can be programmed: low temperature and high temperature.
Programming must be carried out so that the high temperature setting is higher than the low temperature setting.
Do you want to program in Celsius or Fahrenheit?
1. Celsius
2. Fahrenheit.
1 - Celsius
2 - Fahrenheit
------------------------
Celsius
The seat temperature can be set between 0°C and 43°C.
Which seat do you want to reprogram:
1. Left seat
2. Right seat.
1 - Checking the left seat
2 - Checking the right seat
------------------------
Fahrenheit
The seat temperature can be set between 32°F and 109.4°F.
Which seat do you want to reprogram:
1. Left seat
2. Right seat.
1 - Checking the left seat
2 - Checking the right seat
------------------------
Checking the left seat
Read off the programming by clicking on the VCT2000 symbol.
To change the seat temperature, mark the desired value in the scrolling list and start programming.
Programming must be carried out so that the high temperature setting is higher than the low temperature setting.
Continue - Save the programmed value
------------------------
Checking the right seat
Read off the programming by clicking on the VCT2000 symbol.
To change the seat temperature, mark the desired value in the scrolling list and start programming.
Programming must be carried out so that the high temperature setting is higher than the low temperature setting.
Continue - Save the programmed value
------------------------
Checking the left seat
Read off the programming by clicking on the VCT2000 symbol.
To change the seat temperature, mark the desired value in the scrolling list and start programming.
Programming must be carried out so that the high temperature setting is higher than the low temperature setting.
Continue - Save the programmed value
------------------------
Checking the right seat
Read off the programming by clicking on the VCT2000 symbol.
To change the seat temperature, mark the desired value in the scrolling list and start programming.
Programming must be carried out so that the high temperature setting is higher than the low temperature setting.
Continue - Save the programmed value
------------------------
Save the programmed value
To ensure that the programmed information is stored, click on the VCT2000 symbol to force the entry.
-------------------------------------------------
Do you want to program any more parameters?
Yes - Programming procedures
No - Fault Found
-------------------------------------------------
Programming the home safe lights
Programming the home safe lights
Programming the home safe lights
The home safe lights can be programmed to stay on for a longer or shorter time according to the wishes of the customer.
The factory setting is 30 seconds. The time can be set to 0, 30, 60 or 90 seconds.
Read off the programming by clicking on the VCT2000 symbol.
To change the time set, mark the desired value in the scrolling list and start programming.
Continue - Save the programmed value
------------------------
Save the programmed value
To ensure that the programmed information is stored, click on the VCT2000 symbol to force the entry.
-------------------------------------------------
Programming the daytime running lamps
Programming daytime running lamps
Programming daytime running lamps
Three different daytime running light functions can be programmed:
1. Low beam in all switch positions except the parking light position (Flex zero)
Position light switch:
OFF:Parking and daytime running lamps or Xenon lamps are activated depending on the signal from the twilight sensor.
Parking lamps:Only parking lamps activated.
On:Parking and Xenon lamps are activated.
2. The light switch functioning on the basis of: off, parking light and low beam (Flex standard)
Position light switch:
OFF:Daytime running lamps are activated. If the twilight sensor registers insufficient light, all lighting is switched off (Xenon lamps are not activated).
Parking lamps:Only parking lamps activated.
On:Parking and Xenon lamps are activated.
3. Low beam always on regardless of the position of the light switch (Flex low)
Position light switch:
OFF:Parking and daytime running lamps or Xenon lamps are activated depending on the signal from the twilight sensor.
Parking lamps:Parking and Xenon lamps are activated.
On:Parking and Xenon lamps are activated.
It is essential that the legal requirements of each country are followed.
Note! It is not permitted to change this programming in the Canadian market.
Read off the programming by clicking on the VCT2000 symbol.
To change the setting, mark the desired value in the scrolling list and start programming.
Continue - Save the programmed value
------------------------
Save the programmed value
To ensure that the programmed information is stored, click on the VCT2000 symbol to force the entry.
-------------------------------------------------
Programming the wiper function for the rear windshield (5 door models)
Programming the wiper function for the rear windshield (5 door models)
Programming the wiper function for the rear windshield (5 door models)
- The wiper function for the rear windshield can be programmed. There are two versions:
1. The rear windshield wiper can only be activated manually.
2. The rear windshield wiper can be activated automatically when back-up (reverse) gear is selected and the front wipers are activated.
Read off the programming by clicking on the VCT2000 symbol.
To change the setting, mark the desired value in the scrolling list and start programming.
Continue - Save the programmed value
------------------------
Save the programmed value
To ensure that the programmed information is stored, click on the VCT2000 symbol to force the entry.
-------------------------------------------------
Programming the time delay, fuel tank filler cover lock
Programming the time delay, fuel tank filler cover lock
Programming the time delay, fuel tank filler cover lock
- The time delay between the car being locked using a remote control or the key until the fuel tank filler cover locks can be programmed. There are two alternatives:
1. 10 minute time delay.
2. 0 minute time delay.
Read off the programming by clicking on the VCT2000 symbol.
To change the setting, mark the desired value in the scrolling list and start programming.
Continue - Save the programmed value
------------------------
Save the programmed value
To ensure that the programmed information is stored, click on the VCT2000 symbol to force the entry.
-------------------------------------------------
Programming the warning for low beam position (Bi-Xenon)
Programming the warning for low beam position (Bi-Xenon)
Programming the warning for low beam position (Bi-Xenon)
- The warning for low beam position can be programmed on cars with Bi-Xenon lamps and where the light switch is programmed as flexstd. There are two positions:
1. Off
2. On.
Read off the programming by clicking on the VCT2000 symbol.
To change the setting, mark the desired value in the scrolling list and start programming.
Continue - Save the programmed value
------------------------
Save the programmed value
To ensure that the programmed information is stored, click on the VCT2000 symbol to force the entry.
-------------------------------------------------