Operation CHARM: Car repair manuals for everyone.
Home >> Audi >> 2001 >> TT Coupe (8N3) L4-1.8L Turbo (AWP) >> Repair and Diagnosis >> Powertrain Management >> Computers and Control Systems >> Testing and Inspection >> Scan Tool Testing and Procedures >> Scan Tool Testing >> With Generic Scan Tool >> Diagnostic Mode 6: Check Results - Not Continuously Monitored

Diagnostic Mode 6: Check Results - Not Continuously Monitored



Diagnostic Mode 6: Check Test Results Of Components That Are Not Continuously Monitored

Function
This diagnostic mode displays the test results of emission relevant components and systems which are not continuously monitored.

The values of the individual test results must reach the specified value or must be within the min.- and max.- limits.

Test-ID Component, System
01: Catalytic converter
03: Secondary Air Injection (AIR) system
05: Tank ventilation system
09: Coolant thermostat monitoring

Test-ID 01: Catalytic converter

Test requirements
- There must not be any DTCs stored in DTC memory, Diagnostic mode 3: Check DTC memory. Diagnostic Mode 3: Check DTC Memory
- Coolant temperature must be at least 80 degree C, Diagnostic mode 1: Check measuring values; PID 5, Coolant temperature. Diagnostic Mode 1: Check Measured Values

Procedure
- Read readiness code. Readiness Code, Function
- Let engine run at idle.
- Under address word 33, select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
- Select the "Test-ID 01: Catalytic converter".
- Check specified values at idle.

Evaluation test-ID 01: Catalytic converter







- End diagnosis and switch ignition off.

If the specified values are exceeded:
- Replace catalytic converter:
- Vehicles with Front Wheel Drive (FWD), item 4 .
- Vehicles with All Wheel Drive (AWD), item 6 .

Continuation for all vehicles
- Erase DTC memory of Engine Control Module (ECM), Diagnostic mode 4: Reset/erase diagnostic data. Diagnostic Mode 4: Reset/Erase Diagnostic Data
- Generate readiness code. Readiness Code, Generating

Test-ID 03: Secondary Air Injection (AIR) system

Test requirements
- There must not be any DTCs stored in DTC memory, Diagnostic mode 3: Check DTC memory. Diagnostic Mode 3: Check DTC Memory

Procedure
- Read readiness code. Readiness Code, Function
- Let engine run at idle.
- Under address word 33, select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
- Select the "Test-ID 03: Secondary Air Injection (AIR) system"
- Check specified values at idle.

Evaluation test-ID 03: Secondary Air Injection (AIR) system







- End diagnosis and switch ignition off.

If the specified values are not reached:
- Check secondary air system for proper seal. Secondary Air Injection (AIR) System, Checking For Proper Seal
- Check Secondary Air Injection (AIR) Pump Motor -V101-. Secondary Air Injection (AIR) Pump Motor -V101-, Checking
- Erase DTC memory of Engine Control Module (ECM), Diagnostic mode 4: Reset/erase diagnostic data. Diagnostic Mode 4: Reset/Erase Diagnostic Data
- Generate readiness code. Readiness Code, Generating

Test-ID 05: Tank ventilation system

Test requirements
- There must not be any DTCs stored in DTC memory, Diagnostic mode 3: Check DTC memory. Diagnostic Mode 3: Check DTC Memory
- Coolant temperature must be 80 to 110 degree C, Diagnostic mode 1: Check measuring values; PID 5, Coolant temperature. Diagnostic Mode 1: Check Measured Values

Procedure
- Read readiness code. Readiness Code, Function
- Let engine run at idle.
- Under address word 33, select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
- Select the "Test-ID 05: Tank ventilation system".
- Check specified values at idle.

Evaluation test-ID 05: Tank ventilation system







If the specified values are exceeded:
- EVAP canister system, checking for proper seal.
- Check Evaporative Emission (EVAP) Canister Purge Regulator Valve -N80-. EVAP Canister Purge Regulator Valve -N80-, Checking
- Leak detection pump (LDP) -V144-. Leak Detection Pump (LDP), Checking
- Erase DTC memory of Engine Control Module (ECM), Diagnostic mode 4: Reset/erase diagnostic data. Diagnostic Mode 4: Reset/Erase Diagnostic Data
- Generate readiness code. Readiness Code, Generating

Test-ID 09: Coolant thermostat monitoring

Test requirement
- There must not be any DTCs stored in DTC memory, Diagnostic mode 3: Check DTC memory. Diagnostic Mode 3: Check DTC Memory

Procedure
- Read readiness code. Readiness Code, Function
- Let engine run at idle.
- Under address word 33, select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
- Select the "Test-ID 09: Engine Coolant Temperature (ECT) sensor".
- Check specified values at idle.

Evaluation test-ID 09: Coolant thermostat monitoring







- End diagnosis and switch ignition off.

If specified value is not obtained:
- Check coolant regulator:
pro multis · About Operation CHARM