Diagnostic Mode 6: Checking Test Results of Components That Are Not Continuously Monitored

Diagnostic Mode 6: Checking Test Results Of Components That Are Not Continuously Monitored

Diagnostic Mode 06 displays the test results of emission related components and systems which are not continuously monitored.

The values of the individual test results must reach the specified value or must be within the min. and max. limits.

NOTE: Depending on diagnostic tester and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).

Test requirements
- Exhaust system must be properly sealed between catalytic converter and cylinder head.
- No DTCs in the DTC memory. .
- Coolant temperature at least 80 degrees C.

Work procedure
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select the desired "Test-ID" ..

The current minimum and maximum values will be displayed on the diagnostic tester screen.

Test-ID (Hex-ID) Component or System
01 ($01): Oxygen Sensor Monitor Bank 1 - Sensor 1
02 ($02): Oxygen Sensor Monitor Bank 1 - Sensor 2
05 ($05): Oxygen Sensor Monitor Bank 2 - Sensor 1
06 ($06): Oxygen Sensor Monitor Bank 2 - Sensor 2
33 ($21): Catalyst Monitor Bank 1
34 ($22): Catalyst Monitor Bank 2
$3A (58): Fuel Tank EVAP System Leak Test (0.090)
59 (3B): EVAP Monitor (0.40)
60 (3C): EVAP Monitor (0.20)
61 (3D): Purge Flow Monitor
65 ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1
66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2
69 ($45): Oxygen Sensor Heater Monitor Bank 2 - Sensor 1
70 ($46): Oxygen Sensor Heater Monitor Bank 2 - Sensor 2
162 ($A2): Mis-Fire Cylinder 1 Data
163 ($A4): Mis-Fire Cylinder 2 Data
164 ($A4): Mis-Fire Cylinder 3 Data
165 ($A5): Mis-Fire Cylinder 4 Data
166 ($A4): Mis-Fire Cylinder 5 Data
167 ($A7): Mis-Fire Cylinder 6 Data

Test-ID 01 ($01): Oxygen Sensor Monitor Bank 1 - Sensor 1.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 01 ($01)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 02 ($02): Oxygen Sensor Monitor Bank 1- Sensor 2 .
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 02 ($02)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 05 ($05): Oxygen Sensor Monitor Bank 2 - Sensor 1 .
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 05 ($05)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 06 ($06): Oxygen Sensor Monitor Bank 2 - Sensor 2 .
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 06 ($06)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 33 ($21): Catalyst Monitor Bank 1.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 33 ($21)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 34 ($22): Catalyst Monitor Bank 2.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 34 ($22)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

$3A (58): Fuel Tank EVAP System Leak Test (0.090).
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 59 ($3B)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 59 (3B): EVAP Monitor (0.040).
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 59 ($3B)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 60 (3C): EVAP Monitor (0.020).
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 60 ($3C)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 61 (3D): Purge Flow Monitor.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 61 ($3D)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 65 ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 65 ($41)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 69 ($45): Oxygen Sensor Heater Monitor Bank 2 - Sensor 1.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 69 ($45)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure .
- Switch the ignition off.
- End of diagnosis.

Test-ID 66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 66 ($42)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 70 ($46): Oxygen Sensor Heater Monitor Bank 2 - Sensor 2.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
- Select "Test-ID 70 ($46)".
- Select the desired "Test-ID".
- Check specified values at idle.







- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 162 ($A2): Mis-Fire Cylinder 1 Data.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 162 ($A2)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.







- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 163 ($A4): Mis-Fire Cylinder 2 Data.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 163 ($A4)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.







- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 164 ($A4): Mis-Fire Cylinder 3 Data.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 164 ($A4)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.







- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 165 ($A5): Mis-Fire Cylinder 4 Data.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 165 ($A5)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.







- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 166 ($A4): Mis-Fire Cylinder 5 Data.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 166 ($A4)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.







- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.

Test-ID 167 ($A7): Mis-Fire Cylinder 6 Data.
- Connect the diagnostic tester.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 167 ($A7)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.







- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
- End of diagnosis.